25 open source boards using the ATtiny85

Real designs built with the ATtiny85, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

25 boardsClear filters|Most starred

How designs wire the ATtiny85

Read from the KiCad layouts of 22 open source designs, one per repository: what each pin of the ATtiny85 connects to, and the resistors, capacitors and other passives placed on it.

  • The PB2 pin has a series resistor on 11 of 22 designs, most often 1 kΩ (then 470 Ω).
  • The XTAL1/PB3 pin has a series resistor on 10 of 22 designs, most often 1 kΩ (then 68 Ω).
  • The AREF/PB0 pin has a series resistor on 10 of 22 designs, most often 1 kΩ (then 470 Ω).
  • The PB1 pin has a series resistor on 10 of 22 designs, most often 1 kΩ (then 470 Ω).
XTAL1/PB3pin 2Connected to: Signal 82%
  • Series resistor on 45% · 1 kΩ (2), 68 Ω (2), 120 Ω (2)
XTAL2/PB4pin 3Connected to: Signal 73% · not connected 27%
  • Series resistor on 41% · 68 Ω (2), 1 kΩ (2), 120 Ω (2)
GNDpin 4Connected to: GND 73% · a signal 27%
AREF/PB0pin 5Connected to: A connector 64%
  • Series resistor on 45% · 1 kΩ (5), 470 Ω (2), 120 Ω (2)
PB1pin 6Connected to: A connector 55%
  • Series resistor on 45% · 1 kΩ (3), 470 Ω (2), 120 Ω (2)
PB2pin 7Connected to: A connector 45%
  • Series resistor on 50% · 1 kΩ (4), 470 Ω (3), 120 Ω (2)
VCCpin 8Connected to: 5V 73% · a signal 27%

1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include 2-digit-Turbo-Display by wiretap-retro, TVBGone by curiouselectric, PiFanIrHat by llegoff and C128-link232 by ytmytm.

The ATtiny85 in open source designs

The gallery holds 25 open source boards using the ATtiny85 from 22 GitHub repositories; a typical one measures about 48.5 × 30 mm and carries around 15 components.

100% are two-layer designs, the rest use four layers or more, and 24% carry an open source license.

The most starred is 2-digit-Turbo-Display by wiretap-retro.

Microcontrollers on boards using the ATtiny85

ATtiny85: common questions

Where can I find a ATtiny85 reference design?

Each of the 25 boards on this page is a real design using the ATtiny85. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the ATtiny85 PB2 pin?

The PB2 pin has a series resistor on 11 of 22 designs, most often 1 kΩ (then 470 Ω). Counted from the KiCad layouts of 22 open source designs using the ATtiny85.

What resistor goes on the ATtiny85 XTAL1/PB3 pin?

The XTAL1/PB3 pin has a series resistor on 10 of 22 designs, most often 1 kΩ (then 68 Ω). Counted from the KiCad layouts of 22 open source designs using the ATtiny85.

What resistor goes on the ATtiny85 AREF/PB0 pin?

The AREF/PB0 pin has a series resistor on 10 of 22 designs, most often 1 kΩ (then 470 Ω). Counted from the KiCad layouts of 22 open source designs using the ATtiny85.

Which microcontrollers do boards using the ATtiny85 use?

Most are built on AVR/Arduino (25).

How big is a typical board using the ATtiny85?

The median is 48.5 × 30 mm, and 100% are two-layer designs.

What is the most popular open source board using the ATtiny85?

By GitHub stars, 2-digit-Turbo-Display by wiretap-retro, with 12 stars.

Can I simulate one of these boards using the ATtiny85 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part