ATtiny85-Catch me-BCL-2-v1.0
rsedak·ATtiny85-Catch-me-BCL-2-v1.0·design_files/attiny85_catch_me_bcl-2.kicad_pcb
About the ATtiny85-Catch me-BCL-2-v1.0 PCB
ATtiny85-Catch me-BCL-2-v1.0 is an open source AVR/Arduino PCB design by rsedak, published on GitHub under the Custom license license. It is a 2-layer board measuring 78.1 × 64.7 mm, with 24 components from 7 distinct parts.
Its main chip is the ATtiny85, from the AVR/Arduino family. By type, the board carries 12 resistors, 7 diodes, 2 switches, 1 IC, 1 battery holder and 1 capacitor.
From the project
My friend Zvonimir Lapov asked me if I could design THT PCB which would be used in primary school student education. Purpose of 'Catch me BCL-2' module is student education. It shows advantages of charlieplexing with seven BI-color LEDs. This version is designed for the case when the BI-color LED has a brighter LED on pin 3.
Introduction ============ My friend Zvonimir Lapov asked me if I could design THT PCB which would be used in primary school student education. Purpose of 'Catch me BCL-2' module is student education. It shows advantages of charlieplexing with seven BI-color LEDs. This version is designed for the case when the BI-color LED has a brighter LED on pin 3. There are many variations of bi-color LEDs on the market, so you will need to define the resistors yourself.

Main components on the ATtiny85-Catch me-BCL-2-v1.0
ATtiny85-Catch me-BCL-2-v1.0 bill of materials (BOM)
24 components, 7 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ATtiny85 | DIP-8_W7.62mm | U1 |
| 1 | Battery_Cell | BatteryHolder_Keystone_1060_1x2032 | BT1 |
| 1 | SW_Push | SW_PUSH-12mm | SW1 |
| 1 | SW_Push_SPDT | SW_Slide_SPDT_1P2TC_right_angle | SW2 |
| 7 | LED_Dual_AKA | LED_D5.0mm-3 | D1, D2, D3, D4, D5, D6, D7 |
| 1 | 0.1uF | C_Rect_L7.0mm_W2.5mm_P5.00mm | C1 |
| 12 | 120R | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2, R3, R4, R5, R6, R7, R8 +4 |
ATtiny85-Catch me-BCL-2-v1.0 design files
The KiCad project lives in the rsedak/ATtiny85-Catch-me-BCL-2-v1.0 repository on GitHub; these links point at the commit this page was built from.
ATtiny85-Catch me-BCL-2-v1.0: common questions
What microcontroller does the ATtiny85-Catch me-BCL-2-v1.0 use?
The ATtiny85-Catch me-BCL-2-v1.0 is built around the ATtiny85, from the AVR/Arduino family.
How big is the ATtiny85-Catch me-BCL-2-v1.0 PCB?
The ATtiny85-Catch me-BCL-2-v1.0 measures 78.1 × 64.7 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the ATtiny85-Catch me-BCL-2-v1.0?
24 components, from 7 distinct parts. The full bill of materials is listed on this page.
Where can I download the ATtiny85-Catch me-BCL-2-v1.0 design files?
From the rsedak/ATtiny85-Catch-me-BCL-2-v1.0 repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the ATtiny85-Catch me-BCL-2-v1.0 design in my own project?
It is published under Custom license, which limits how it may be reused; read the license before building on it.
Can I test firmware for the ATtiny85-Catch me-BCL-2-v1.0 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k