Attiny85 Catch me v1.0
rsedak·attiny85_Catch_me_v1.0·design_files/attiny85_catch_me.kicad_pcb
About the Attiny85 Catch me v1.0 PCB
Attiny85 Catch me v1.0 is an open source AVR/Arduino PCB design by rsedak, published on GitHub under the Custom license license. It is a 2-layer board measuring 78.1 × 64.7 mm, with 16 components from 7 distinct parts.
Its main chip is the ATtiny85, from the AVR/Arduino family. By type, the board carries 7 LEDs, 4 resistors, 2 switches, 1 IC, 1 battery holder and 1 capacitor.
From the project
My friend Zvonimir Lapov asked me if I could design THT PCB which would be used in primary school student education. Purpose of 'Catch me' module is student education. It shows advantages of charlieplexing. It is published under Attribution-ShareAlike 4.0 International (CC BY-SA 4.0) license. I hope you will enjoy it.
Introduction ============ My friend Zvonimir Lapov asked me if I could design THT PCB which would be used in primary school student education. Purpose of 'Catch me' module is student education. It shows advantages of charlieplexing. Photo by Robert Sedak
Contributor ------------ - Robert Sedak — features, programming, schematic design, CAD design - Zvonimir Lapov - idea, case for PCB

Main components on the Attiny85 Catch me v1.0
Attiny85 Catch me v1.0 bill of materials (BOM)
16 components, 7 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ATtiny85 | DIP-8_W7.62mm | U1 |
| 1 | Battery_Cell | BatteryHolder_Keystone_1060_1x2032 | BT1 |
| 1 | SW_Push | SW_PUSH-12mm | SW1 |
| 1 | SW_Push_SPDT | SW_Slide_SPDT_1P2TC_right_angle | SW2 |
| 7 | LED | LED_D5.0mm | LED1, LED2, LED3, LED4, LED5, LED6, LED7 |
| 1 | 0.1uF | C_Rect_L4.6mm_W2.0mm_P2.50mm_MKS02_FKP02 | C1 |
| 4 | 470R | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2, R3, R4 |
Attiny85 Catch me v1.0 design files
The KiCad project lives in the rsedak/attiny85_Catch_me_v1.0 repository on GitHub; these links point at the commit this page was built from.
Attiny85 Catch me v1.0: common questions
What microcontroller does the Attiny85 Catch me v1.0 use?
The Attiny85 Catch me v1.0 is built around the ATtiny85, from the AVR/Arduino family.
How big is the Attiny85 Catch me v1.0 PCB?
The Attiny85 Catch me v1.0 measures 78.1 × 64.7 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Attiny85 Catch me v1.0?
16 components, from 7 distinct parts. The full bill of materials is listed on this page.
Where can I download the Attiny85 Catch me v1.0 design files?
From the rsedak/attiny85_Catch_me_v1.0 repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Attiny85 Catch me v1.0 design in my own project?
It is published under Custom license, which limits how it may be reused; read the license before building on it.
Can I test firmware for the Attiny85 Catch me v1.0 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k