Robot-Nano-Shield

rsedak·Robot-Nano-Shield·design_files/robot_nano_shield.kicad_pcb

Robot-Nano-Shield layout, top view — open source AVR/Arduino board by rsedak

About the Robot-Nano-Shield

Robot-Nano-Shield is an open source AVR/Arduino PCB design by rsedak, published on GitHub under the Custom license license. It is a 2-layer board measuring 64 × 72 mm, with 26 components from 14 distinct parts.

Its main chip is the Arduino_Nano_v3.x, from the AVR/Arduino family. Other key parts include the LM7805_TO220. By type, the board carries 13 connectors, 7 resistors, 2 diodes, 2 capacitors, 1 IC and 1 module.

It belongs with the robotics & motion, dev boards & breakouts and wearables designs in this gallery.

From the project

Robot Nano Shield is Arduino Nano based shield for robots with dimentions compatibile with Lego(TM) liftarms.

Robot Nano Shield is Arduino Nano based shield for robots with dimentions compatibile with Lego(TM) liftarms. For voltage stability L78S05CV Positive-Voltage regulator is used, and for power supply you can use two Li-Ion 18650 batteries. During programming please keep in mind next design rules: - D0-D1 — reserved for Bluetooth module (TX have onboard resistor voltage devider for HC-06 module) - D2-D7 — reserved for H-bridge module (aka. L298N Dual H Bridge) - D8 — reserved for servo motor - D9-11 — reserved for RGB LED with onboard resistors - D12-D13 — reserved for ultrasonic sensor HC-SR04…

Robot-Nano-Shield, from the project README
From the project README

Main components on the Robot-Nano-Shield

Robot-Nano-Shield bill of materials (BOM)

26 components, 14 distinct parts.

QtyPartRefs
1
LM7805_TO220
U1
1
Arduino_Nano_v3.x
A1
9
Conn_01x03_Male
J2, J3, J4, J5, J6, J8, J9, J11 +1
1
Conn_01x01_Male
J7
1
Conn_01x04_Female
J10
2
Conn_01x04_Female
J12, J14
1
LED_RCGB
D1
1
1N5400
D2
1
10uF/25V
C1
1
220uF/10V
C2
2
1K
R1, R4
2
560R
R2, R3
1
2K
R5
2
10K
R6, R7

Robot-Nano-Shield design files

The KiCad project lives in the rsedak/Robot-Nano-Shield repository on GitHub; these links point at the commit this page was built from.

Robot-Nano-Shield: common questions

What microcontroller does the Robot-Nano-Shield use?

The Robot-Nano-Shield is built around the Arduino_Nano_v3.x, from the AVR/Arduino family.

How big is the Robot-Nano-Shield?

The Robot-Nano-Shield measures 64 × 72 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Robot-Nano-Shield?

26 components, from 14 distinct parts. The full bill of materials is listed on this page.

Where can I download the Robot-Nano-Shield design files?

From the rsedak/Robot-Nano-Shield repository on GitHub, which has the KiCad layout; the links under Design files point to each one.

Can I use the Robot-Nano-Shield design in my own project?

It is published under Custom license, which limits how it may be reused; read the license before building on it.

Can I test firmware for the Robot-Nano-Shield without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

Similar boards