RFID-Gwent

s-grundner·RFID-Gwent·manufacturing/Reader_Module/Reader_Module.kicad_pcb

RFID-Gwent PCB layout, top view — open source STM32 board by s-grundner

About the RFID-Gwent PCB

RFID-Gwent is an open source STM32 PCB design by s-grundner, published on GitHub under the Apache-2.0 license. It is a 4-layer board measuring 28.8 × 48.8 mm, with 60 components from 29 distinct parts.

Its main chip is the STM32L431KBU6, from the STM32 family. Other key parts include the SN65HVD230 and USBLC6-2. By type, the board carries 38 capacitors, 11 resistors, 3 ICs, 3 inductors, 2 diodes and 1 crystal.

From the project

Electronic Gwent Game from the Witcher Series

RFID-Gwent, from the project README
From the project README

Main components on the RFID-Gwent

STM32L431KBU6SN65HVD230USBLC6-2

RFID-Gwent bill of materials (BOM)

60 components, 29 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
STM32L431KBU6
U1
1
SN65HVD230
U2
1
USBLC6-2
U3
1
13.56MHZ
13.56MHz
Y1
1
Antenna_Loop
AE1
1
C79174
NRST
SW1
1
TRF7964ARHBR
D1
1
C2296
WT
D2
1
C1015
100 @ 100MHz
FB2
2
150N
150n
L1, L2
9
100N
100n
C1, C2, C3, C8, C20, C21, C22, C23 +1
10
2U2
2u2
C4, C5, C7, C9, C11, C13, C15, C19 +2
5
10N
10n
C6, C10, C12, C14, C16
3
27P
27p
C17, C18, C26
2
47P
47p
C25, C38
1
68P
68p
C27
3
1N2
1n2
C30, C32, C33
1
1N8
1n8
C31
2
680P
680p
C34, C36
1
220P
220p
C35
Show 9 more
QtyPartRefs
1
100P
100p
C37
1
47K
47k
R1
1
1K5
1k5
R2
1
100R
R3
1
10K
10k
R4
4
56R
R5, R6, R7, R8
1
1K5
1k5
R9
1
680R
R10
1
0R
R11

RFID-Gwent design files

The KiCad project lives in the s-grundner/RFID-Gwent repository on GitHub; these links point at the commit this page was built from.

RFID-Gwent: common questions

What microcontroller does the RFID-Gwent use?

The RFID-Gwent is built around the STM32L431KBU6, from the STM32 family.

How big is the RFID-Gwent PCB?

The RFID-Gwent measures 28.8 × 48.8 mm, has 4 copper layers and is 1.6062 mm thick.

How many components are on the RFID-Gwent?

60 components, from 29 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the RFID-Gwent design files?

From the s-grundner/RFID-Gwent repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the RFID-Gwent design in my own project?

Yes, under the terms of its Apache-2.0 license, which s-grundner chose for the repository.

Can I test firmware for the RFID-Gwent without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards