220 open source boards using the SN65HVD230
Real designs built with the SN65HVD230, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Huvud
bondus
42 × 42 mm116 parts4LGPL-3.0373STM32
EPS
rgw3d
85 × 85 mm629 parts4LGPL-3.0157PIC
CANBuster
GBert
100 × 100 mm177 parts2LNo license99Rx72t 100 pga usb
hirakuni45
120 × 80 mm109 parts2LBSD-3-Clause86STM32
TurboCAN
henrikssn
43 × 43 mm84 parts2LNo license82ESP8266
Tesla-Front-Drive-Unit
damienmaguire
190.5 × 176.6 mm196 parts4LNo license59STM32
Frankenso
rusefi
154.1 × 161.7 mm614 parts2LNo license48STM32
FalCAN
AndersBNielsen
76.5 × 30.9 mm54 parts4LNo license48ESP32
Monolith
luftaquila
96 × 74.4 mm112 parts2LCustom license43ESP32
OpenAirScope
emertcakir
100 × 75 mm247 parts4LMIT26ESP32
OkayCAN
jglim
64.8 × 41 mm32 parts2LMIT24ESP8266
MG ZS V2
damienmaguire
180 × 120 mm161 parts4LGPL-3.016STM32
Bms hardware
jsphuebner
64.5 × 85.1 mm68 parts4LGPL-3.014STM32
SMDUv3
sabanekko3
57 × 25.9 mm66 parts4LCC-BY-NC-4.013ESP32
CAN-to-WiFi-Converter-Dongle-
ampnics
47.5 × 71.5 mm68 parts2LNo license10STM32
Eps
OSUSat
80 × 80 mm357 parts6LMIT8STM32
Stm32f0-can mini breakout
NerdyProjects
91.4 × 53.7 mm98 parts2LNo license8STM32
Candash
miekush
100 × 80 mm90 parts2LCustom license7STM32
BMW-K1200LT-ABS-Conversion
OstapFerensovych
61.4 × 49 mm63 parts2LMIT7ESP32
Vandal
blinken
147 × 92 mm213 parts2LGPL-3.06TMS320F28377S-
LE-TOM
86.4 × 69.9 mm172 parts3LNo license6ESP32
${Title}
miata-bot
78.5 × 95 mm152 parts4LNo license6ESP32
SensactHs
klaus-liebler
100 × 86.5 mm317 parts2LApache-2.04STM32
BigSur
ParadigmHyperloop
196.4 × 70 mm145 parts2LCustom license4STM32
Lre avio daq2
IITB-Rocket-Team-Avionics
4.5 × 13.4 mm136 parts2LMIT4ESP32
PNP MOBO V2
GabrielD98
110 × 80 mm114 parts4LMIT4STM32
Spel bldc esc
koson
84.5 × 60 mm91 parts4LNo license4Devboard
DistRap
100 × 100 mm54 parts2LCustom license4ESP32
Can bus
satspares
48 × 42 mm20 parts2LMIT4STM32
Openinverter hw mainboard mini
llange
56.8 × 67.3 mm96 parts2LCC-BY-SA-4.03STM32
PDU
OpenSkyHawk
96.6 × 63.9 mm67 parts2LCC-BY-NC-4.03ESP32
4F5LCD
Code99it
155 × 78 mm49 parts2LMIT3- schematic only · 4 partsNXP
Cycloidal-Actuator-Design-Project
ratdo6
4 partsNo license3 M52
rusefi
145 × 118 mm226 parts2LNo license2ESP32
PickleRick
icl-rocketry
100 × 37 mm196 parts6LMIT2RP2040/RP2350
DC32 CHV Badge Board
car-hacking-village
194.6 × 93.3 mm150 parts4LNo license2
How designs wire the SN65HVD230
Read from the KiCad layouts of 142 open source designs, one per repository: what each pin of the SN65HVD230 connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 95 of 142 designs, most often 100 nF (then 10 µF).
- The VREF pin is left unconnected on 105 of 141 designs (VREF on 20, a signal on 15).
- The CANH pin has a series resistor on 86 of 139 designs, most often 120 Ω (then 60 Ω).
- The CANL pin has a series resistor on 77 of 140 designs, most often 120 Ω (then 60 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 2 | Connected to: GND 90% | — |
| VCCpin 3 | Connected to: 3.3V 87% |
|
| VREFpin 5 | Connected to: Not connected 74% | — |
| CANLpin 6 | Connected to: A connector 77% |
|
| CANHpin 7 | Connected to: A connector 77% |
|
| RSpin 8 | Connected to: Signal 66% · GND 30% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include CanTactDist by bondus, AVIONICS BOARD by rgw3d, BPi-CAN by GBert and Rx72t 100 pga usb by hirakuni45.
The SN65HVD230 in open source designs
The gallery holds 220 open source boards using the SN65HVD230 from 145 GitHub repositories; a typical one measures about 80.3 × 67.3 mm and carries around 77 components.
60% are two-layer designs, the rest use four layers or more, and 42% carry an open source license.
The most starred is Huvud by bondus.
Parts used alongside the SN65HVD230
Microcontrollers on boards using the SN65HVD230
What boards using the SN65HVD230 are built for
SN65HVD230: common questions
Where can I find a SN65HVD230 reference design?
Each of the 220 boards on this page is a real design using the SN65HVD230. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the SN65HVD230 VCC pin?
The VCC pin has a decoupling capacitor on 95 of 142 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 142 open source designs using the SN65HVD230.
How is the SN65HVD230 VREF pin connected?
The VREF pin is left unconnected on 105 of 141 designs (VREF on 20, a signal on 15). Counted from the KiCad layouts of 142 open source designs using the SN65HVD230.
What resistor goes on the SN65HVD230 CANH pin?
The CANH pin has a series resistor on 86 of 139 designs, most often 120 Ω (then 60 Ω). Counted from the KiCad layouts of 142 open source designs using the SN65HVD230.
What parts are used alongside the SN65HVD230?
The AMS1117-3.3, ESP32-S3, USBLC6-2SC6, MAX77827AEFD+T and ESP32-WROOM-32 appear in the most repositories here.
Which microcontrollers do boards using the SN65HVD230 use?
Most are built on ESP32 (77), STM32 (74), RP2040/RP2350 (11) and NXP (10).
How big is a typical board using the SN65HVD230?
The median is 80.3 × 67.3 mm, and 60% are two-layer designs.
What is the most popular open source board using the SN65HVD230?
By GitHub stars, Huvud by bondus, with 373 stars.
Can I simulate one of these boards using the SN65HVD230 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.