25 open source boards using the USBLC6-2
Real designs built with the USBLC6-2, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
MMDVM HS Hat
mathisschmieder
65.1 × 30.2 mm79 parts4LNo license200STM32
Proteus
mck1117
135 × 82.5 mm348 parts4LNo license50Imxrt1020-module
martinribelotta
136 × 58 mm133 parts2LBSD-3-Clause37Omega dock new
valerionew
42.9 × 26.4 mm18 parts2LCC-BY-SA-4.037STM32
Polygonus
FOME-Tech
103 × 82.4 mm299 parts4LNo license21AVR/Arduino
Splitty ergonomic keyboard
schodet
133.4 × 100.3 mm89 parts2LMIT13STM32
Midi fader
kcuzner
73.7 × 78.7 mm91 parts2LApache-2.012STM32
Hard wookey motherboard
wookey-project
43 × 66 mm68 parts4LCERN-OHL-1.210STM32
ReST32 Main
berryelectronics
100 × 100 mm168 parts2LNo license7STM32
ALL
eddyem
200.5 × 70.9 mm138 parts4LGPL-3.06Omega2-Berrydock
berryelectronics
50 × 50 mm86 parts2LNo license4STM32
Fannyadams
svofski
154.9 × 102.9 mm300 parts2LNo license2STM32
Topiary-TrimBot
griffinross2
190.5 × 160 mm251 parts4LGPL-3.02STM32
NEOM 0
wal99d
27 × 50.3 mm29 parts4LNo license2STM32
Fsorx
haunma
86 × 96 mm152 parts4LCC-BY-SA-4.01STM32
RFID-Gwent
s-grundner
28.8 × 48.8 mm60 parts4LApache-2.01STM32
Blackmagic clone
sergiomd4
43.6 × 27 mm41 parts2LCC0-1.01STM32
Fome mc
halbritt
162 × 115 mm462 parts4LNo license0STM32
BlackBoxProbeBig
Squantor
44 × 44 mm75 parts4LMIT0STM32
Fieldmill
haunma
102 × 102 mm112 parts4LCC-BY-SA-4.01FPGA
ICEBreaker bitsy
frohro
38.1 × 17.8 mm98 parts4LNo license0STM32
Fieldmill2
haunma
102 × 102 mm112 parts4LCC-BY-SA-4.01STM32
BlackBoxProbeSmall
Squantor
44 × 29 mm60 parts4LMIT0STM32
Brushless board
robotronik
60 × 62.5 mm57 parts2LNo license1STM32
Brushless board
robotronik
60 × 62.5 mm57 parts2LNo license1
How designs wire the USBLC6-2
Read from the KiCad layouts of 22 open source designs, one per repository: what each pin of the USBLC6-2 connects to, and the resistors, capacitors and other passives placed on it.
- The I/O1 pins have a series resistor on 12 of 22 designs, most often 22 Ω (then 27 Ω).
- The I/O2 pins have a series resistor on 12 of 22 designs, most often 22 Ω (then 1.5 kΩ).
- The VBUS pin has a decoupling capacitor on 12 of 22 designs, most often 100 nF (then 4.7 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| I/O1pin 1, 6 | Connected to: A connector 52%, the microcontroller 27% |
|
| GNDpin 2 | Connected to: GND 95% | — |
| I/O2pin 3, 4 | Connected to: A connector 52%, the microcontroller 27% |
|
| VBUSpin 5 | Connected to: 5V 73% · a signal 27% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include MMDVM HS Hat by mathisschmieder, Proteus by mck1117, Imxrt1020-module by martinribelotta and Omega dock new by valerionew.
The USBLC6-2 in open source designs
The gallery holds 25 open source boards using the USBLC6-2 from 22 GitHub repositories; a typical one measures about 73.7 × 66 mm and carries around 91 components.
60% use four copper layers or more, and 56% carry an open source license.
The most starred is MMDVM HS Hat by mathisschmieder.
Parts used alongside the USBLC6-2
Microcontrollers on boards using the USBLC6-2
What boards using the USBLC6-2 are built for
USBLC6-2: common questions
Where can I find a USBLC6-2 reference design?
Each of the 25 boards on this page is a real design using the USBLC6-2. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the USBLC6-2 I/O1 pin?
The I/O1 pins have a series resistor on 12 of 22 designs, most often 22 Ω (then 27 Ω). Counted from the KiCad layouts of 22 open source designs using the USBLC6-2.
What resistor goes on the USBLC6-2 I/O2 pin?
The I/O2 pins have a series resistor on 12 of 22 designs, most often 22 Ω (then 1.5 kΩ). Counted from the KiCad layouts of 22 open source designs using the USBLC6-2.
What decoupling capacitors do designs use on the USBLC6-2 VBUS pin?
The VBUS pin has a decoupling capacitor on 12 of 22 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 22 open source designs using the USBLC6-2.
What parts are used alongside the USBLC6-2?
The 74HC2G17GW, LMR14020, LPS25HB, MCP6004T-I/ST and REF3033 appear in the most repositories here.
Which microcontrollers do boards using the USBLC6-2 use?
Most are built on STM32 (20), AVR/Arduino (1) and FPGA (1).
How big is a typical board using the USBLC6-2?
The median is 73.7 × 66 mm, and 40% are two-layer designs.
What is the most popular open source board using the USBLC6-2?
By GitHub stars, MMDVM HS Hat by mathisschmieder, with 200 stars.
Can I simulate one of these boards using the USBLC6-2 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.