L1 Project Winder
salinda-yasas-99·L1_Project_Winder·Pcb design/Full pcb/level1/level1.kicad_pcb
About the L1 Project Winder PCB
L1 Project Winder is an open source AVR/Arduino PCB design by salinda-yasas-99, published on GitHub. It is a 2-layer board measuring 330.2 × 243.8 mm, with 53 components from 19 distinct parts.
Its main chip is the ATmega32-16P, from the AVR/Arduino family. Other key parts include the CD4052B. By type, the board carries 10 inductors, 4 capacitors, 3 ICs, 2 resistors, 1 transistor and 1 connector.
From the project
hardware porject
Here is the system that is able to automate the process of winding transformers. Also, the system is able to measure transformer bobbin parameters and decide on relevant wire gauges according to the transformer input and output.
Main components on the L1 Project Winder
L1 Project Winder bill of materials (BOM)
53 components, 19 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 3 | CD4052B | DIP-16_W7.62mm | U14, U15, U16 |
| 1 | 2N3055 | TO-39-3_Window | Q1 |
| 1 | Servo | PinSocket_1x12_P1.00mm_Vertical | J10 |
| 1 | 5V | Altech_AK300_1x02_P5.00mm_45-Degree | 5V |
| 1 | 12V | Altech_AK300_1x02_P5.00mm_45-Degree | 12V |
| 4 | 74HCT4051 | DIP-16_W7.62mm | 74HC4051_1, 74HC4051_2, 74HC4051_3, 74HC4051_4 |
| 1 | Buzzer | Buzzer_12x9.5RM7.6 | BZ1 |
| 4 | CD4052B | DIP-16_W7.62mm_LongPads | CD4052_1, CD4052_2, CD4052_3, CD4052_4 |
| 1 | Conn_01x08_Female | PinHeader_1x08_P1.00mm_Vertical_SMD_Pin1Right | LCD_DATA1 |
| 1 | R_Potentiometer | Potentiometer_Bourns_3314J_Vertical | LCD_VEE1 |
| 2 | ATmega32-16P | DIP-40_W15.24mm | Master1, Slave1 |
| 2 | SW_Push | SW_PUSH_6mm_H7.3mm | RS_2, RS_M1 |
| 10 | Screw_Terminal_01x04 | TerminalBlock_Phoenix_MKDS-1,5-4_1x04_P5.00mm_Horizontal | STEP_BOB1, STEP_CUTM1, STEP_CUTTER1, STEP_PRI1, STEP_SEC1, STEP_TAP1, STEP_TAP2, STEP_TAPPM1 +2 |
| 2 | 16Mhz | Crystal_HC49-4H_Vertical | crystal1, crystal2 |
| 1 | Conn_01x08_Female | PinSocket_1x08_P1.27mm_Vertical | keypad1 |
| 2 | Conn_01x06_Female | JST_EH_B6B-EH-A_1x06_P2.50mm_Vertical | ultra_con1, ultra_pow1 |
| 10 | L293D | DIP-16_W7.62mm | L293D1, L293D2, L293D3, L293D4, L293D5, L293D6, L293D7, L293D8 +2 |
| 4 | 22 uf | C_Disc_D11.0mm_W5.0mm_P7.50mm | C1, C2, C3, C4 |
| 2 | 1k | R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R1, R2 |
L1 Project Winder design files
The KiCad project lives in the salinda-yasas-99/L1_Project_Winder repository on GitHub; these links point at the commit this page was built from.
L1 Project Winder: common questions
What microcontroller does the L1 Project Winder use?
The L1 Project Winder is built around the ATmega32-16P, from the AVR/Arduino family.
How big is the L1 Project Winder PCB?
The L1 Project Winder measures 330.2 × 243.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the L1 Project Winder?
53 components, from 19 distinct parts. The full bill of materials is listed on this page.
Where can I download the L1 Project Winder design files?
From the salinda-yasas-99/L1_Project_Winder repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the L1 Project Winder design in my own project?
The repository has no license, so all rights stay with salinda-yasas-99. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the L1 Project Winder without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k