EPS

SatelliteApplicationsCatapult·PocketQube·hardware/Electronic/PCB Designs/EPS/KiCAD/EPS/EPS.kicad_pcb

EPS PCB layout, top view — open source NXP board by SatelliteApplicationsCatapult

About the EPS PCB

EPS is an open source NXP PCB design by SatelliteApplicationsCatapult, published on GitHub. It is a board measuring 42 × 42 mm, with 93 components from 40 distinct parts.

Its main chip is the MKL02Z16VFM4, from the NXP family. Other key parts include the LTC4413EDDPBF, TPS2553DRVT, TPS22960DCNR, 3MMPILAR and BQ24079. By type, the board carries 34 ICs, 29 resistors, 13 capacitors and 1 test point.

It belongs with the power & battery and test & measurement designs in this gallery.

From the project

1. Four IXYS solar panels as a power source

1. Four IXYS solar panels as a power source

2. Two LTC3105 based MPPT circuits to maximise the solar power generated

3. A MAX8606ETD charge management IC to facilitate safe battery charging and effective system load management.

4. A regulation circuit including: A watchdog timer to detect unresponsive MCUs (STWD100PYW83F) A brownout monitor to detect invalid voltages (BU4231G-TR) A 3V3 LDO regulator with active-high enable, allowing supervisor ICs or external MCUs to trigger a reset (MIC5353-3.3YMT_)

Main components on the EPS

LTC4413EDDPBFTPS2553DRVTTPS22960DCNR3MMPILARBQ24079DEBUG-TPBAT41ABS25_32.768KHZPMV40UN2FAN4010IL6X_F113NCP706AMX300TAGMKL02Z16VFM4TAG_CONNECTEL3H7

EPS bill of materials (BOM)

93 components, 40 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
LTC4413EDDPBF
U1
1
TPS2553DRVT
U9
3
TPS22960DCNR
U10, U11, U12
4
3MMPILAR
U$1, U$5, U$6, U$7
1
BQ24079
U$2
5
DEBUG-TP
U$3, U$16, U$23, U$27, U$28
6
BAT41
U$4, U$10, U$14, U$17, U$31, U$32
1
ABS25_32.768KHZ
U$8
3
PMV40UN2
U$11, U$12, U$15
1
—
U$13
4
FAN4010IL6X_F113
U$18, U$19, U$25, U$26
1
NCP706AMX300TAG
U$20
1
MKL02Z16VFM4
U$21
1
TAG_CONNECT
U$22
1
EL3H7
U$24
5
JST-B2B-ZH
BAT56, SOL1, SOL2, SOL3, SOL4
1
BU4231G-TR
BU4331G-TR56
1
INA211A
INA210AIDCKT56
2
WE-TPC-744031100
IND1, IND2
2
LTC3105
MPPT1, MPPT2
Show 20 more
QtyPartRefs
1
FX8C-060P-SV2(92)
PQ60_HEADER56
1
FX8C-060S-SV(92)
PQ60_RECEPTACLE56
1
961102-5604-AR
PWR56
1
—
SJ1
1
STWD100PYW83F
STWD100PYW83F56
1
TPTP07R
TP1
6
10uF
C1, C2, C4, C5, C6, C8
5
1uF
C3, C7, C22, C25, C26
1
10nF
C21
1
1nF
C23
2
1.3M
R1, R4
2
330K
R2, R5
2
501K
R3, R6
14
10K
R7, R8, R9, R10, R15, R18, R20, R21 +6
4
0.15R, 1%
R13, R22, R36, R37
1
2.2K
R16
1
3.3K
R17
1
0.015R 1%
R19
1
150R
R33
1
47K
R40

EPS design files

The KiCad project lives in the SatelliteApplicationsCatapult/PocketQube repository on GitHub; these links point at the commit this page was built from.

EPS: common questions

What microcontroller does the EPS use?

The EPS is built around the MKL02Z16VFM4, from the NXP family.

How big is the EPS PCB?

The EPS measures 42 × 42 mm and is 1.6 mm thick.

How many components are on the EPS?

93 components, from 40 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the EPS design files?

From the SatelliteApplicationsCatapult/PocketQube repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.

Can I use the EPS design in my own project?

The repository has no license, so all rights stay with SatelliteApplicationsCatapult. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the EPS without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug NXP firmware against it before you order a PCB.

More boards in PocketQube

Similar boards