13 open source boards using the EL3H7
Real designs built with the EL3H7, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
Noname 2
ARTS-Laboratory
63.5 × 55.9 mm32 parts2LCC-BY-SA-4.01RP2040/RP2350
UCNC Pi Board
staskaaa-netizen
200 × 150 mm314 parts2LNo license0RP2040/RP2350
Iw-8-controller
mekatrol
167.3 × 103 mm198 parts2LNo license0STM32
Controls-Leader
lhr-solar
79.3 × 97.5 mm177 parts2LNo license0RP2040/RP2350
RC lights control MFC-03
luckymuniza
86.5 × 65.3 mm106 parts2LNo license0RP2040/RP2350
RC lights control MFC-01
luckymuniza
96.1 × 63.5 mm74 parts2LNo license0AVR/Arduino
Prototype
ARTS-Laboratory
60.2 × 52.8 mm32 parts2LCC-BY-SA-4.01NXP
EPS
SatelliteApplicationsCatapult
42 × 42 mm93 partsNo license0Shield v0.9.2
ARTS-Laboratory
71.5 × 50.3 mm32 parts2LCC-BY-SA-4.01RP2040/RP2350
Output controller
mekatrol
238 × 122 mm161 parts2LNo license0RP2040/RP2350
Controller
mekatrol
140 × 100 mm146 parts2LNo license0RP2040/RP2350
Basic controller
mekatrol
68 × 88 mm46 parts4LNo license0RP2040/RP2350
Temperature controller
mekatrol
68 × 88 mm46 parts4LNo license0
How designs wire the EL3H7
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the EL3H7 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 1 has a series resistor on 4 of 6 designs, most often 10 kΩ (then 100 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 100% |
|
| Pin 3 | Connected to: GND 50% · a signal 50% |
|
| Pin 4 | Connected to: The microcontroller 50% · 5V 33% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Noname 2 by ARTS-Laboratory, Controls-LeaderPCB by lhr-solar, RC lights control MFC-01 by luckymuniza and RC lights control MFC-03 by luckymuniza.
The EL3H7 in open source designs
The gallery holds 13 open source boards using the EL3H7 from 7 GitHub repositories; a typical one measures about 79.3 × 88 mm and carries around 93 components.
83% are two-layer designs, the rest use four layers or more, and 23% carry an open source license.
The most starred is Shield v0.9.2 by ARTS-Laboratory.
Parts used alongside the EL3H7
Microcontrollers on boards using the EL3H7
What boards using the EL3H7 are built for
EL3H7: common questions
Where can I find a EL3H7 reference design?
Each of the 13 boards on this page is a real design using the EL3H7. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the EL3H7 pin 1?
Pin 1 has a series resistor on 4 of 6 designs, most often 10 kΩ (then 100 Ω). Counted from the KiCad layouts of 6 open source designs using the EL3H7.
Which microcontrollers do boards using the EL3H7 use?
Most are built on RP2040/RP2350 (8), AVR/Arduino (2), NXP (1) and STM32 (1).
How big is a typical board using the EL3H7?
The median is 79.3 × 88 mm, and 83% are two-layer designs.
What is the most popular open source board using the EL3H7?
By GitHub stars, Shield v0.9.2 by ARTS-Laboratory, with 1 stars.
Can I simulate one of these boards using the EL3H7 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.