AVR
Selmakrgzz·AVR·Devboard/Devboard-Design/myDevboard/myDevboard.kicad_pcb
About the AVR PCB
AVR is an open source AVR/Arduino PCB design by Selmakrgzz, published on GitHub. It is a 2-layer board measuring 20.2 × 37.7 mm, with 14 components from 11 distinct parts.
Its main chip is the ATtiny404-SS, from the AVR/Arduino family. Other key parts include the MIC5504-3.3YM5. By type, the board carries 4 connectors, 3 capacitors, 2 ICs, 2 diodes, 2 resistors and 1 switch.
From the project
Embedded programming in C/C++
Main components on the AVR
AVR bill of materials (BOM)
14 components, 11 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | MIC5504-3.3YM5 | SOT-23-5 | U1 |
| 1 | ATtiny404-SS | SOIC-14_3.9x8.7mm_P1.27mm | U2 |
| 1 | USB_B_Micro | USB_Micro-B_Amphenol_10104110_Horizontal | J1 |
| 1 | AVR-UPDI-6 | PinHeader_2x03_P2.54mm_Vertical | J2 |
| 2 | Conn_01x07_Pin | PinHeader_1x07_P2.54mm_Vertical | J3, J4 |
| 1 | SW_Omron_B3FS | SW_TH_Tactile_Omron_B3F-10xx | SW1 |
| 2 | LED | LED_0603_1608Metric | D1, D2 |
| 1 | 100nF | C_0603_1608Metric | C1 |
| 2 | 1u | C_0603_1608Metric | C3, C4 |
| 1 | 4k | R_0603_1608Metric | R1 |
| 1 | 2K | R_0603_1608Metric | R2 |
AVR design files
The KiCad project lives in the Selmakrgzz/AVR repository on GitHub; these links point at the commit this page was built from.
AVR: common questions
What microcontroller does the AVR use?
The AVR is built around the ATtiny404-SS, from the AVR/Arduino family.
How big is the AVR PCB?
The AVR measures 20.2 × 37.7 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the AVR?
14 components, from 11 distinct parts. The full bill of materials is listed on this page.
Where can I download the AVR design files?
From the Selmakrgzz/AVR repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the AVR design in my own project?
The repository has no license, so all rights stay with Selmakrgzz. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the AVR without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k