9 open source boards using the ATtiny404-SS
Real designs built with the ATtiny404-SS, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
Genesis 6button
rfmerrill
61.7 × 36.8 mm26 parts2LMIT5AVR/Arduino
Ornament2022
Chris-Johnston
1.6 × 1.6 mm20 parts2LNo license2AVR/Arduino
Seriallight
eurovibes
50 × 50 mm59 parts2LNo license0AVR/Arduino
Mini ultrasonic
jackestar
26.1 × 15 mm50 parts2LMIT0AVR/Arduino
Rf room sensor hw
dselcan
50.8 × 44 mm32 parts2LBSD-3-Clause0AVR/Arduino
Ornament2025
Chris-Johnston
90.1 × 90.1 mm18 parts2LNo license0AVR/Arduino
AVR
Selmakrgzz
20.2 × 37.7 mm14 parts2LNo license0AVR/Arduino
Access control door servo
aaronds
52.6 × 22.1 mm26 parts2LNo license0AVR/Arduino
Stepper
hisashin
31 × 49 mm28 parts2LGPL-3.047
How designs wire the ATtiny404-SS
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the ATtiny404-SS connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 7 of 8 designs, most often 100 nF (then 1 µF).
- The PA5 pin has a series resistor on 6 of 8 designs, most often 1 kΩ (then 2 kΩ).
- The PB2 pin has a series resistor on 4 of 8 designs, most often 1 kΩ.
- The PB1 pin has a series resistor on 4 of 8 designs, most often 1 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VCCpin 1 | Connected to: 5V 100% |
|
| PA5pin 3 | Connected to: A connector 25% |
|
| PB2pin 7 | Connected to: A connector 38% |
|
| PB1pin 8 | Connected to: A connector 38% |
|
| PB0pin 9 | Connected to: A connector 38% |
|
| GNDpin 14 | Connected to: GND 100% | — |
8 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Genesis 6button by rfmerrill, Ornament2022 by Chris-Johnston, Access control door servo by aaronds and Ornament2025 by Chris-Johnston.
The ATtiny404-SS in open source designs
The gallery holds 9 open source boards using the ATtiny404-SS from 9 GitHub repositories; a typical one measures about 50 × 37.7 mm and carries around 26 components.
100% are two-layer designs, the rest use four layers or more, and 44% carry an open source license.
The most starred is Stepper by hisashin.
Microcontrollers on boards using the ATtiny404-SS
What boards using the ATtiny404-SS are built for
ATtiny404-SS: common questions
Where can I find a ATtiny404-SS reference design?
Each of the 9 boards on this page is a real design using the ATtiny404-SS. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the ATtiny404-SS VCC pin?
The VCC pin has a decoupling capacitor on 7 of 8 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 8 open source designs using the ATtiny404-SS.
What resistor goes on the ATtiny404-SS PA5 pin?
The PA5 pin has a series resistor on 6 of 8 designs, most often 1 kΩ (then 2 kΩ). Counted from the KiCad layouts of 8 open source designs using the ATtiny404-SS.
What resistor goes on the ATtiny404-SS PB2 pin?
The PB2 pin has a series resistor on 4 of 8 designs, most often 1 kΩ. Counted from the KiCad layouts of 8 open source designs using the ATtiny404-SS.
Which microcontrollers do boards using the ATtiny404-SS use?
Most are built on AVR/Arduino (9).
How big is a typical board using the ATtiny404-SS?
The median is 50 × 37.7 mm, and 100% are two-layer designs.
What is the most popular open source board using the ATtiny404-SS?
By GitHub stars, Stepper by hisashin, with 47 stars.
Can I simulate one of these boards using the ATtiny404-SS before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.