HardLabs

Blackmagic clone

sergiomd4·blackmagic-clone·Hardware/blackmagic.kicad_pcb

Blackmagic clone PCB layout, top view — open source STM32 board by sergiomd4
Simulate this board

About the Blackmagic clone PCB

Blackmagic clone is an open source STM32 PCB design by sergiomd4, published on GitHub under the CC0-1.0 license. It is a 2-layer board measuring 43.6 × 27 mm, with 41 components from 23 distinct parts.

Its main chip is the STM32F103RB, from the STM32 family. Other key parts include the TXS0108EPW, USBLC6-2 and NCP1117. By type, the board carries 15 resistors, 13 capacitors, 4 ICs, 4 diodes, 2 connectors and 1 transistor.

From the project

Board focused on embedded microcontrollers debugging

Black Magic Clone ========================================

Black Magic is an easy-to-use board used for debugging embedded microcontrollers. It supports several targets from manufacturers such as STMicroelectronics, Atmel, Nordic Semiconductor, NXP, Texas Instruments, Freescale, Silicon Labs, Xilinx or Raspberry Pi.

GNU debugger ------------------- The Black Magic GNU DeBugger (GDB) server features: Automatic target detection No need for target specific configuration scripts Easily scriptable Interface to the host computer does not require special drivers Full debugging functionality Works…

Main components on the Blackmagic clone

TXS0108EPWUSBLC6-2NCP1117STM32F103RB

Blackmagic clone bill of materials (BOM)

41 components, 23 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
TXS0108EPW
U1
1
USBLC6-2
U2
1
NCP1117
U3
1
STM32F103RB
U4
1
BC846
Q1
1
8 MHz
X1
1
USB_Mini_B
J2
1
Conn_01x02_Male
J3
1
SW_Push
S1
1
green
D1
1
red
D2
2
yellow
D3, D4
3
10u
C1, C5, C6
8
100n
C2, C7, C8, C9, C10, C11, C12, C13
2
18p
C3, C4
4
1k
R1, R5, R12, R14
2
22
R2, R3
1
1k5
R4
1
10M
R6
1
330
R7
Show 3 more
QtyPartRefs
4
390
R8, R9, R10, R11
1
10k
R13
1
100
R15

Blackmagic clone design files

The KiCad project lives in the sergiomd4/blackmagic-clone repository on GitHub; these links point at the commit this page was built from.

Blackmagic clone: common questions

What microcontroller does the Blackmagic clone use?

The Blackmagic clone is built around the STM32F103RB, from the STM32 family.

How big is the Blackmagic clone PCB?

The Blackmagic clone measures 43.6 × 27 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Blackmagic clone?

41 components, from 23 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Blackmagic clone design files?

From the sergiomd4/blackmagic-clone repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Blackmagic clone design in my own project?

Yes, under the terms of its CC0-1.0 license, which sergiomd4 chose for the repository.

Can I test firmware for the Blackmagic clone without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards