EWU-ASME-SDC-2026-Robot

SethHibpshman·EWU-ASME-SDC-2026-Robot·hardware/PCB KiCAD/ASME-eFest.kicad_pcb

EWU-ASME-SDC-2026-Robot PCB layout, top view — open source AVR/Arduino board by SethHibpshman

About the EWU-ASME-SDC-2026-Robot PCB

EWU-ASME-SDC-2026-Robot is an open source AVR/Arduino PCB design by SethHibpshman, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 57 × 61 mm, with 7 components from 3 distinct parts.

Its main chip is the Arduino_Nano_Every, from the AVR/Arduino family. Other key parts include the DCDC_StepDown. By type, the board carries 5 switches, 1 IC and 1 module.

It belongs with the robotics & motion designs in this gallery.

From the project

EWU ASME team’s remote controlled garbage truck for the 2026 Student Design Competition. 3D printed PETG chassis, rear wheel drive with servo steering, robotic arm, rotary dumper, and custom electronics. 3rd place overall.

- Overview - Functionality - Operating Requirements - Drive and Steering - Manipulation and Dumping - Radio Control Mapping - Input Processing and Failsafe - System Design - Hardware - Power Architecture - Battery Selection Analysis - PCB Design - Power Distribution Board - Software - Mechanical Design - Design Tradeoffs - Competition Results - Lessons Learned and Future Improvements - Bill of Materials - Team - AI Disclosure - License

EWU-ASME-SDC-2026-Robot, from the project README
From the project README

Main components on the EWU-ASME-SDC-2026-Robot

DCDC_StepDownArduino_Nano_Every

EWU-ASME-SDC-2026-Robot bill of materials (BOM)

7 components, 3 distinct parts.

QtyPartRefs
1
DCDC_StepDown
U1
1
Arduino_Nano_Every
A2
5
Motor_Servo
S1, S2, S3, S4, S5

EWU-ASME-SDC-2026-Robot design files

The KiCad project lives in the SethHibpshman/EWU-ASME-SDC-2026-Robot repository on GitHub; these links point at the commit this page was built from.

EWU-ASME-SDC-2026-Robot: common questions

What microcontroller does the EWU-ASME-SDC-2026-Robot use?

The EWU-ASME-SDC-2026-Robot is built around the Arduino_Nano_Every, from the AVR/Arduino family.

How big is the EWU-ASME-SDC-2026-Robot PCB?

The EWU-ASME-SDC-2026-Robot measures 57 × 61 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the EWU-ASME-SDC-2026-Robot?

7 components, from 3 distinct parts. The full bill of materials is listed on this page.

Where can I download the EWU-ASME-SDC-2026-Robot design files?

From the SethHibpshman/EWU-ASME-SDC-2026-Robot repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the EWU-ASME-SDC-2026-Robot design in my own project?

Yes, under the terms of its GPL-3.0 license, which SethHibpshman chose for the repository.

Can I test firmware for the EWU-ASME-SDC-2026-Robot without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

Similar boards