Pilkki

SmallSharky·Pilkki·electronics/pilkki.kicad_pcb

Pilkki PCB layout, top view — open source STM32 board by SmallSharky

About the Pilkki PCB

Pilkki is an open source STM32 PCB design by SmallSharky, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 32 × 20 mm, with 55 components from 31 distinct parts.

Its main chip is the STM32G431KBUx, from the STM32 family. Other key parts include the TPD2EUSB30A, MIC23050-SYML and 74LVC2T45RA3. By type, the board carries 17 capacitors, 16 resistors, 6 ICs, 4 connectors, 4 diodes and 2 transistors.

From the project

SWD flashing tool

Utility to interact with flasher could be found in software folder.

Schematics and PCB (KiCAD) are in electronics folder.

Main components on the Pilkki

Pilkki bill of materials (BOM)

55 components, 31 distinct parts.

QtyPartRefs
1
TPD2EUSB30A
U1
1
MIC23050-SYML
U2
1
STM32G431KBUx
U3
3
74LVC2T45RA3
U4, U5, U6
1
SSM6N35AFE
Q1
1
DMG1023UV
Q2
1
ECS-CTP-8.00-30
Y1
1
USB_C_Receptacle
J1
1
Conn_01x01_Pin
J2
1
Conn_01x08
J3
1
Conn_01x10
J4
1
0ZCK0100FF2E
F1
1
SolderJumper_2_Open
JP1
1
EVQ-P2202M
SW1
1
GREEN
D1
1
RED
D2
1
ORANGE
D3
1
YELLOW
D4
1
BLM15AG102SZ1D
FB1
1
LQM21PN1R0MC0D
L1
Show 11 more
QtyPartRefs
14
0.1u
C1, C2, C3, C5, C8, C9, C10, C11 +6
2
4.7uFx6.3
C4, C7
1
560pF
C6
1
10R
R1
2
5.1K
R2, R3
2
4.7K
R4, R11
6
10K
R5, R6, R7, R9, R10, R12
1
4.7R
R8
2
100
RN1, RN2
1
330
RN3
1
33
RN4

Pilkki design files

The KiCad project lives in the SmallSharky/Pilkki repository on GitHub; these links point at the commit this page was built from.

Pilkki: common questions

What microcontroller does the Pilkki use?

The Pilkki is built around the STM32G431KBUx, from the STM32 family.

How big is the Pilkki PCB?

The Pilkki measures 32 × 20 mm, has 2 copper layers and is 1.09 mm thick.

How many components are on the Pilkki?

55 components, from 31 distinct parts. The full bill of materials is listed on this page.

Where can I download the Pilkki design files?

From the SmallSharky/Pilkki repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Pilkki design in my own project?

Yes, under the terms of its GPL-3.0 license, which SmallSharky chose for the repository.

Can I test firmware for the Pilkki without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards