Slider potentiometer breakout hardware design
SolderedElectronics·Slider-potentiometer-breakout-hardware-design·CAD/V1.1.1/Slider_potentiometer.kicad_pcb
About the Slider potentiometer breakout hardware design
Slider potentiometer breakout hardware design is an open source PCB design by SolderedElectronics, published on GitHub under the TAPR-OHL-1.0 license. It is a 2-layer board measuring 86 × 22 mm, with 9 components from 4 distinct parts.
By type, the board carries 2 relays, 2 capacitors and 1 resistor.
It belongs with the dev boards & breakouts designs in this gallery.
From the project
Hardware design, BOM, gerbers and 3D files for Slider-potentiometer-breakout designed by Soldered Electronics.
Potentiometers are well known all around, and the sliding potentiometer is just one of its versions.You’ve probably seen it in some music equipment, and now you have the chance to add it to your project!
This repository contains all design files for Slider potentiometer breakout, organized as follows:
- CAD folder: Contains KiCAD design files, including: - Schematics - PCB layout - Panel PCB layout - Source 3D files in Fusion360, if any - All files are sorted by version with a detailed change log. - OUTPUTS folder: Includes all production-ready files, such as: - Bill of Materials (BOM) and…

Slider potentiometer breakout hardware design bill of materials (BOM)
9 components, 4 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 4 | HOLE_3.2MM HOLE_3.2mm | HOLE_3.2mm | H1, H2, H3, H4 |
| 2 | HEADER_MALE_3X1 | HEADER_MALE_3X1 | K1, K2 |
| 2 | 0.1UF 0.1uF | 0603C | C1, C2 |
| 1 | SLIDER_POT | SLIDER_POT | R1 |
Slider potentiometer breakout hardware design design files
The KiCad project lives in the SolderedElectronics/Slider-potentiometer-breakout-hardware-design repository on GitHub; these links point at the commit this page was built from.
Slider potentiometer breakout hardware design: common questions
How big is the Slider potentiometer breakout hardware design?
The Slider potentiometer breakout hardware design measures 86 × 22 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Slider potentiometer breakout hardware design?
9 components, from 4 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Slider potentiometer breakout hardware design design files?
From the SolderedElectronics/Slider-potentiometer-breakout-hardware-design repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Slider potentiometer breakout hardware design design in my own project?
Yes, under the terms of its TAPR-OHL-1.0 license, which SolderedElectronics chose for the repository.
Similar boards
Breakout 112pin Connector
rusefi
174 × 58 mm39 parts2LGPL-3.01.2kEecv breakout
rusefi
140.8 × 53.7 mm9 parts4LGPL-3.01.2kBreakout 60pin EEC-IV
rusefi
139.7 × 62.2 mm15 parts2LGPL-3.01.2k134pin 7-967288-1
rusefi
139.7 × 73.7 mm38 parts2LGPL-3.01.2k88 Pin Vag Breakout
rusefi
142 × 58 mm91 parts2LGPL-3.01.2kRj45 breakout
rene-dev
15.2 × 53.8 mm3 parts2LGPL-3.0979