Linefollower
souptik-samanta·linefollower
About the Linefollower PCB
Linefollower is an open source AVR/Arduino PCB design by souptik-samanta, published on GitHub. It is a 2-layer board measuring 90 × 75 mm, with 27 components from 18 distinct parts.
Its main chip is the NANO, from the AVR/Arduino family. Other key parts include the ROB-14450 and LM7805_TO220. By type, the board carries 15 connectors, 4 resistors, 3 capacitors, 2 ICs, 1 module and 1 buzzer.
Main components on the Linefollower
Linefollower bill of materials (BOM)
27 components, 18 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ROB-14450 | MODULE_ROB-14450 | U1 |
| 1 | LM7805_TO220 | TO-220-3_Vertical | U2 |
| 1 | NANO | Arduino_Nano | A1 |
| 1 | BLUETOOTH | PinSocket_1x06_P2.54mm_Vertical | J1 |
| 1 | RLS08 | PinHeader_1x12_P2.54mm_Vertical | J2 |
| 1 | MOTOR 1 | TerminalBlock_CUI_TB007-508-02_1x02_P5.08mm_Horizontal | J3 |
| 1 | MOTOR 2 | TerminalBlock_CUI_TB007-508-02_1x02_P5.08mm_Horizontal | J4 |
| 1 | POWER IN | TerminalBlock_CUI_TB007-508-02_1x02_P5.08mm_Horizontal | J5 |
| 1 | I2C HEADER | PinHeader_1x04_P2.54mm_Vertical | J6 |
| 9 | jumper | PinHeader_1x01_P2.54mm_Vertical | J8, J9, J10, J11, J12, J13, J14, J15 +1 |
| 1 | Buzzer | Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | Start | SW_PUSH_6mm | SW1 |
| 1 | 470uF | CP_Radial_D10.0mm_P5.00mm | C1 |
| 2 | C | C_Radial_D8.0mm_H7.0mm_P3.50mm | C2, C3 |
| 1 | 1k | R_Axial_DIN0309_L9.0mm_D3.2mm_P15.24mm_Horizontal | R1 |
| 1 | 2k | R_Axial_DIN0309_L9.0mm_D3.2mm_P15.24mm_Horizontal | R2 |
| 1 | 100 | R_Axial_DIN0309_L9.0mm_D3.2mm_P15.24mm_Horizontal | R3 |
| 1 | 10k | R_Axial_DIN0309_L9.0mm_D3.2mm_P15.24mm_Horizontal | R4 |
Linefollower design files
The KiCad project lives in the souptik-samanta/linefollower repository on GitHub; these links point at the commit this page was built from.
- LayoutLFR PCB.kicad_pcb
- SchematicLFR PCB.kicad_sch
Linefollower: common questions
What microcontroller does the Linefollower use?
The Linefollower is built around the NANO, from the AVR/Arduino family.
How big is the Linefollower PCB?
The Linefollower measures 90 × 75 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Linefollower?
27 components, from 18 distinct parts. The full bill of materials is listed on this page.
Where can I download the Linefollower design files?
From the souptik-samanta/linefollower repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Linefollower design in my own project?
The repository has no license, so all rights stay with souptik-samanta. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Linefollower without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k