18 open source boards using the ROB-14450
Real designs built with the ROB-14450, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RP2040/RP2350
ControlBoard v1
0x23
64 × 85 mm21 parts2LMIT1.9kSTM32
Noah hardware
GonzaCerv
120 × 100 mm122 parts2LMIT28STM32
Line-Follower-Robot-Using-STM32F103C8T6-with-TCRT-5000
bonavirak
99.8 × 82 mm32 parts2LMIT11ESP32
WRO FE 2026 FoxRobotics
Nakashima26
87.2 × 93.9 mm20 parts2LMIT1AVR/Arduino
16299-balancing robot
SuperTails
95 × 82 mm43 parts4LNo license0AVR/Arduino
SumoBot v1
choicebuilds
88 × 60 mm33 parts4LNo license0AVR/Arduino
Linefollower
souptik-samanta
90 × 75 mm27 parts2LNo license0ESP32
StealTheMoon
choicebuilds
130 × 130 mm22 parts4LNo license0ESP32
Unplugged
Crriminson
181.2 × 167.1 mm15 parts2LMIT0Asda
angelmon091
75 × 50.3 mm12 parts2LNo license0- schematic only · 57 partsRP2040/RP2350
Archive fuzz
ravinder-Olivier
57 partsNo license0 ESP32
Self Balancing Bot
Shantu-2580
120 × 75 mm11 parts2LNo license0Projeto PCA9685
BitDogLab
70 × 70 mm17 parts2LCERN-OHL-S-2.0204ESP32
PID Line Follower
Sreeram-Ramesh
130 × 140 mm12 parts2LMIT0ESP32
Pami n20 V2
Rami-Troudi
80 × 65 mm30 parts2LNo license1ESP32
Pami n20 Chimique
Rami-Troudi
67.4 × 50.4 mm18 parts2LNo license1NXP
Schematic
RoboJackets
83.5 × 57 mm30 parts2LMIT9ESP32
Pami n20 Chimique rev-89
Rami-Troudi
86.5 × 60.9 mm18 parts2LNo license1
How designs wire the ROB-14450
Read from the KiCad layouts of 15 open source designs, one per repository: what each pin of the ROB-14450 connects to, and the resistors, capacitors and other passives placed on it.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VMpin 1 | Connected to: 12V 60% · a signal 33% | — |
| VCCpin 2 | Connected to: 3.3V 100% | — |
| GNDpin 3, 8, 9 | Connected to: GND 96% | — |
11 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include ControlBoard v1 by 0x23, Projeto PCA9685 by BitDogLab, Noah hardware by GonzaCerv and Line-Follower-Robot-Using-STM32F103C8T6-with-TCRT-5000 by bonavirak.
The ROB-14450 in open source designs
The gallery holds 18 open source boards using the ROB-14450 from 16 GitHub repositories; a typical one measures about 88 × 75 mm and carries around 22 components.
82% are two-layer designs, the rest use four layers or more, and 44% carry an open source license.
The most starred is ControlBoard v1 by 0x23.
Parts used alongside the ROB-14450
Microcontrollers on boards using the ROB-14450
What boards using the ROB-14450 are built for
ROB-14450: common questions
Where can I find a ROB-14450 reference design?
Each of the 18 boards on this page is a real design using the ROB-14450. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What parts are used alongside the ROB-14450?
The ESP32-DEVKIT-V1, ESP32-DEVKITC-32D, L7805CV, LM7805_TO220 and RaspberryPi_Pico appear in the most repositories here.
Which microcontrollers do boards using the ROB-14450 use?
Most are built on ESP32 (8), AVR/Arduino (3), RP2040/RP2350 (2) and STM32 (2).
How big is a typical board using the ROB-14450?
The median is 88 × 75 mm, and 82% are two-layer designs.
What is the most popular open source board using the ROB-14450?
By GitHub stars, ControlBoard v1 by 0x23, with 1,850 stars.
Can I simulate one of these boards using the ROB-14450 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.