Stepstick
starfishneuroscience·stepstick·pcb/stepstick.kicad_pcb
About the Stepstick PCB
Stepstick is an open source NXP PCB design by starfishneuroscience, published on GitHub. It is a 4-layer board measuring 28 × 105 mm, with 13 components from 7 distinct parts.
Its main chip is the Teensy4.0, from the NXP family. Other key parts include the Pololu_Breakout_DRV8825. By type, the board carries 4 connectors, 3 modules, 3 capacitors, 2 test points and 1 IC.
It belongs with the robotics & motion designs in this gallery.
From the project
Simple 3x stepper motor controller based on Teensy 4.0 and DRV8825 modules
Stepstick is a simple stepper motor controller board designed to connect a Teensy 4.0 microcontroller to 1-3 DRV8825 stepper motor driver modules (Pololu), in able to control up to 3 steppers.
Stepstick's circuit board design is done in kicad.
Stepstick includes a simple default firmware that can be controlled over a USB serial interface. This firmware prints out instructions over USB serial for how to use it upon bootup. The code depends on AccelStepper and the Arduino Teensy core library.

Main components on the Stepstick
Stepstick bill of materials (BOM)
13 components, 7 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Teensy4.0 | Teensy40 | U1 |
| 3 | Pololu_Breakout_DRV8825 | Pololu_Breakout-16_15.2x20.3mm | A1, A2, A3 |
| 3 | Conn_01x04_Pin | PinHeader_1x04_P2.54mm_Vertical | J1, J2, J4 |
| 1 | PJ-063AH Barrel_Jack_MountingPin | BarrelJack_CUI_PJ-063AH_Horizontal_CircularHoles | J5 |
| 1 | +12V | TestPoint_Loop_D2.54mm_Drill1.5mm_Beaded | TP1 |
| 1 | GND | TestPoint_Loop_D2.54mm_Drill1.5mm_Beaded | TP2 |
| 3 | EEU-EB1J470S 47uF | CP_Radial_D8.0mm_P3.50mm | C1, C2, C3 |
Stepstick design files
The KiCad project lives in the starfishneuroscience/stepstick repository on GitHub; these links point at the commit this page was built from.
- Layoutpcb/stepstick.kicad_pcb
- Schematicpcb/stepstick.kicad_sch
Stepstick: common questions
What microcontroller does the Stepstick use?
The Stepstick is built around the Teensy4.0, from the NXP family.
How big is the Stepstick PCB?
The Stepstick measures 28 × 105 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Stepstick?
13 components, from 7 distinct parts. The full bill of materials is listed on this page.
Where can I download the Stepstick design files?
From the starfishneuroscience/stepstick repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Stepstick design in my own project?
The repository has no license, so all rights stay with starfishneuroscience. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Stepstick without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug NXP firmware against it before you order a PCB.
Similar boards
NXP
32Bit shift register
MaltWhiskey
100 × 54 mm56 parts4LNo license763NXP
Mega-Cube-Board
MaltWhiskey
200 × 54 mm100 parts4LNo license763NXP
MCL6809
MicroCoreLabs
32.3 × 61 mm7 parts4LNo license532NXP
MCL68
MicroCoreLabs
31.6 × 84.1 mm13 parts4LNo license532NXP
MCL65+
MicroCoreLabs
72.6 × 64.1 mm6 parts2LNo license532NXP
MCLZ8
MicroCoreLabs
37.1 × 61.5 mm6 parts4LNo license532