CircuitDesign
SubomiB·CircuitDesign·Wiring Harness Tester/Wiring Harness Tester/Wiring Harness Tester.kicad_pcb
About the CircuitDesign PCB
CircuitDesign is an open source STM32 PCB design by SubomiB, published on GitHub. It is a 4-layer board, with 52 components from 31 distinct parts.
Its main chip is the STM32F103C8T6, from the STM32 family. Other key parts include the TPS62163DSG, MCP1727-3302xMF, SAM-M8Q and PCA9506BS. By type, the board carries 22 capacitors, 13 resistors, 5 ICs, 3 connectors, 3 diodes and 3 inductors.
From the project
Hardware/PCB/FPGA/ASIC Design
Main components on the CircuitDesign
CircuitDesign bill of materials (BOM)
52 components, 31 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TPS62163DSG | WSON-8-1EP_2x2mm_P0.5mm_EP0.9x1.6mm_ThermalVias | U1 |
| 1 | MCP1727-3302xMF | DFN-8-1EP_3x3mm_P0.65mm_EP1.55x2.4mm | U2 |
| 1 | STM32F103C8T6 | LQFP-48_7x7mm_P0.5mm | U3 |
| 1 | SAM-M8Q | ublox_SAM-M8Q | U4 |
| 1 | PCA9506BS | QFN-56-1EP_8x8mm_P0.5mm_EP4.3x4.3mm | U5 |
| 1 | 8MHz | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 12V Jack | BarrelJack_SwitchcraftConxall_RAPC10U_Horizontal | J1 |
| 1 | Micro_SD_Card_Det2 | microSD_HC_Hirose_DM3AT-SF-PEJM5 | J2 |
| 1 | Conn_01x40_Pin | PinHeader_1x40_P2.54mm_Vertical | J4 |
| 2 | SW_SPDT | SW_E-Switch_EG1224_SPDT_Angled | SW1, SW2 |
| 1 | SMAJ15A | D_SMA | D1 |
| 1 | SS34 | D_SMA | D2 |
| 1 | CLX6F-FKC | LED_RGB_PLCC-6 | D3 |
| 2 | 120R | L_0603_1608Metric | FB1, FB2 |
| 1 | 2u2 | L_0402_1005Metric | L1 |
| 5 | 1u | C_0402_1005Metric | C1, C2, C7, C16, C17 |
| 1 | 10u | C_0603_1608Metric | C3 |
| 1 | 22u | C_0805_2012Metric | C4 |
| 3 | 4u7 | C_0603_1608Metric | C5, C10, C22 |
| 1 | 1n | C_0402_1005Metric | C6 |
Show 11 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 10p | C_0402_1005Metric | C8, C9 |
| 8 | 100n | C_0402_1005Metric | C11, C12, C13, C14, C18, C19, C20, C21 |
| 1 | 10n | C_0402_1005Metric | C15 |
| 2 | 100k | R_0402_1005Metric | R1, R2 |
| 3 | 10k | R_0402_1005Metric | R3, R5, R6 |
| 2 | 1k1 | R_0402_1005Metric | R4, R7 |
| 1 | 2k | R_0402_1005Metric | R8 |
| 2 | 1k6 | R_0402_1005Metric | R10, R11 |
| 1 | 75 | R_0402_1005Metric | R12 |
| 1 | 82 | R_0402_1005Metric | R13 |
| 1 | 62 | R_0402_1005Metric | R14 |
CircuitDesign design files
The KiCad project lives in the SubomiB/CircuitDesign repository on GitHub; these links point at the commit this page was built from.
CircuitDesign: common questions
What microcontroller does the CircuitDesign use?
The CircuitDesign is built around the STM32F103C8T6, from the STM32 family.
How big is the CircuitDesign PCB?
The CircuitDesign has 4 copper layers and is 1.6 mm thick.
How many components are on the CircuitDesign?
52 components, from 31 distinct parts. The full bill of materials is listed on this page.
Where can I download the CircuitDesign design files?
From the SubomiB/CircuitDesign repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the CircuitDesign design in my own project?
The repository has no license, so all rights stay with SubomiB. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the CircuitDesign without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k