OpenLog v15
sujitkumar05-pcb·OpenLog_v15
About the OpenLog v15 PCB
OpenLog v15 is an open source AVR/Arduino PCB design by sujitkumar05-pcb, published on GitHub. It is a 2-layer board measuring 40 × 27.5 mm, with 16 components from 14 distinct parts.
Its main chip is the ATmega328P-A, from the AVR/Arduino family. Other key parts include the 3.3V MIC5205. By type, the board carries 4 capacitors, 3 connectors, 3 resistors, 2 ICs, 2 diodes and 1 transistor.
From the project
PCB for logging serial data to a microSD card. Based on the ATmega328 microcontroller. Supports standard FAT16/FAT32 SD cards. Connects easily to any UART/serial device. Useful for data logging without a computer.
Understand serial (UART) communication and data logging concepts.
Learn how to interface a microSD card with embedded systems.
Gain experience in reliable data storage for debugging and monitoring.
Understand low-power, standalone logging module design.
Develop skills for integrating logging modules with microcontrollers. -----
Microcontroller (UART TX): Sends serial data to the OpenLog module.
Main components on the OpenLog v15
OpenLog v15 bill of materials (BOM)
16 components, 14 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 3.3V MIC5205 | SOT-23-5 | U1 |
| 1 | ATmega328P-A | TQFP-32_7x7mm_P0.8mm | U2 |
| 1 | 16MHZ | Crystal_SMD_MicroCrystal_MS1V-T1K | Q1 |
| 1 | ~ | PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | Conn_01x06_Pin | PinHeader_1x06_P2.54mm_Vertical | J2 |
| 1 | Micro_SD_Card | microSD_HC_Molex_104031-0811 | J3 |
| 1 | ~ | PinHeader_1x01_P1.27mm_Vertical | TP1 |
| 1 | GREEN | LED_0805_2012Metric | D1 |
| 1 | BLUE | LED_0805_2012Metric | D2 |
| 1 | 10uF | C_1206_3216Metric | C1 |
| 2 | 0.1uF | C_1206_3216Metric | C2, C3 |
| 1 | 0.1uF | C_1210_3225Metric | C4 |
| 1 | 330 | R_0805_2012Metric | R1 |
| 2 | 1K | R_0805_2012Metric | R2, R3 |
OpenLog v15 design files
The KiCad project lives in the sujitkumar05-pcb/OpenLog_v15 repository on GitHub; these links point at the commit this page was built from.
- LayoutOpenLog_v15.kicad_pcb
- SchematicOpenLog_v15.kicad_sch
OpenLog v15: common questions
What microcontroller does the OpenLog v15 use?
The OpenLog v15 is built around the ATmega328P-A, from the AVR/Arduino family.
How big is the OpenLog v15 PCB?
The OpenLog v15 measures 40 × 27.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the OpenLog v15?
16 components, from 14 distinct parts. The full bill of materials is listed on this page.
Where can I download the OpenLog v15 design files?
From the sujitkumar05-pcb/OpenLog_v15 repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the OpenLog v15 design in my own project?
The repository has no license, so all rights stay with sujitkumar05-pcb. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the OpenLog v15 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k