IRIS-V1
szpuszi·IRIS-V1·hardware/IRIS.kicad_pcb
About the IRIS-V1 PCB
IRIS-V1 is an open source AVR/Arduino PCB design by szpuszi, published on GitHub under the MIT license. It is a 2-layer board measuring 53.3 × 28.2 mm, with 13 components from 10 distinct parts.
Its main chip is the ATTINY85-20P, from the AVR/Arduino family. By type, the board carries 4 resistors, 3 capacitors, 2 diodes, 1 IC, 1 transistor and 1 connector.
From the project
You will also need: - soldering iron and solder - glue (for the case) - double sided tape (for battery, pcb and charging module) - cutting pliers
Main components on the IRIS-V1
IRIS-V1 bill of materials (BOM)
13 components, 10 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ATTINY85-20P ATtiny85-20P | DIP-8_W7.62mm | U1 |
| 1 | IRLZ44N | TO-220-3_Vertical | Q1 |
| 1 | CONN_01X02 Conn_01x02 | PinHeader_1x02_P2.54mm_Vertical | J1 |
| 1 | Button | SW_PUSH_6mm | SW1 |
| 2 | IRLED | LED_D5.0mm | D1, D2 |
| 2 | 1000UF 1000uF | CP_Radial_D8.0mm_P3.50mm | C1, C3 |
| 1 | 100NF 100nF | C_Disc_D4.3mm_W1.9mm_P5.00mm | C2 |
| 2 | 1.5R | R_2512_6332Metric | R1, R4 |
| 1 | 220R | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2 |
| 1 | 10K | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R3 |
IRIS-V1 design files
The KiCad project lives in the szpuszi/IRIS-V1 repository on GitHub; these links point at the commit this page was built from.
- Layouthardware/IRIS.kicad_pcb
- Schematichardware/IRIS.kicad_sch
- BOMManufacturing/BOM.csv
IRIS-V1: common questions
What microcontroller does the IRIS-V1 use?
The IRIS-V1 is built around the ATTINY85-20P, from the AVR/Arduino family.
How big is the IRIS-V1 PCB?
The IRIS-V1 measures 53.3 × 28.2 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the IRIS-V1?
13 components, from 10 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the IRIS-V1 design files?
From the szpuszi/IRIS-V1 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the IRIS-V1 design in my own project?
Yes, under the terms of its MIT license, which szpuszi chose for the repository.
Can I test firmware for the IRIS-V1 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k