Bohlebots rpi cm4-carrier
t0mezz·bohlebots-rpi-cm4-carrier·bohlebots-rpi-cm4-carrier/bohlebots-rpi-cm4-carrier.kicad_pcb
About the Bohlebots rpi cm4-carrier PCB
Bohlebots rpi cm4-carrier is an open source Raspberry Pi PCB design by t0mezz, published on GitHub. It is a 2-layer board measuring 132 × 132 mm, with 36 components from 23 distinct parts.
Its main chip is the Compute_Module_4_Connectors, from the Raspberry Pi family. Other key parts include the USB_Conn_01x05_Pin, DT1446-04SO-7 and C597931. By type, the board carries 8 ICs, 6 connectors, 4 jumpers, 4 resistors, 3 diodes and 2 transformers.
Main components on the Bohlebots rpi cm4-carrier
Bohlebots rpi cm4-carrier bill of materials (BOM)
36 components, 23 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Compute_Module_4_Connectors | Raspberry-Pi-4-Compute-Module | U1 |
| 1 | USB_Conn_01x05_Pin | PinHeader_1x04_P2.54mm_Vertical | U2 |
| 4 | DT1446-04SO-7 | SOT26 | U3, U4, U5, U6 |
| 1 | C597931 Compute_Module_4_Connector_A | Hirose-DF40C-100DS-0.4V(51) | U7 |
| 1 | C597931 Compute_Module_4_Connector_B | Hirose-DF40C-100DS-0.4V(51) | U8 |
| 1 | Miromatch | MICROMATCH-4 | X1 |
| 1 | SI-46001-F | CONN_46001-F_BEL | J1 |
| 1 | power_reference | PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | IO_Conn_02x05 | PinHeader_2x06_P2.54mm_Vertical | J3 |
| 1 | I2C_Conn_1x04 | PinHeader_1x04_P2.54mm_Vertical | J4 |
| 2 | pwr_connector | PinHeader_1x03_P2.54mm_Vertical | J5, J6 |
| 4 | 24_2 | ESCOM_24_2 | ESCON1, ESCON2, ESCON3, ESCON4 |
| 4 | B8B-PH-K | B8B-PH-K | JP1, JP2, JP3, JP4 |
| 1 | Kicker | KICKER | K1 |
| 1 | Luxonis_OAK-FFC-4P_Foothold | Luxonis_OAK-FFC-4P_Foothold | Luxonis OAK-FFP 4P |
| 2 | Taster_LED | TASTER_LED | T1, T2 |
| 1 | LED | LED_D5.0mm_FlatTop | D1 |
| 1 | 5V | D36V28FX | D36V28FX1 |
| 1 | 3.3V | D36V28FX | D36V28FX2 |
| 1 | 100n | C_Radial_D5.0mm_H11.0mm_P2.00mm | C1 |
Show 3 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 10u | C_Radial_D5.0mm_H11.0mm_P2.00mm | C2 |
| 3 | 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2, R3 |
| 1 | 1k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R4 |
Bohlebots rpi cm4-carrier design files
The KiCad project lives in the t0mezz/bohlebots-rpi-cm4-carrier repository on GitHub; these links point at the commit this page was built from.
Bohlebots rpi cm4-carrier: common questions
What microcontroller does the Bohlebots rpi cm4-carrier use?
The Bohlebots rpi cm4-carrier is built around the Compute_Module_4_Connectors, from the Raspberry Pi family.
How big is the Bohlebots rpi cm4-carrier PCB?
The Bohlebots rpi cm4-carrier measures 132 × 132 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Bohlebots rpi cm4-carrier?
36 components, from 23 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Bohlebots rpi cm4-carrier design files?
From the t0mezz/bohlebots-rpi-cm4-carrier repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Bohlebots rpi cm4-carrier design in my own project?
The repository has no license, so all rights stay with t0mezz. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Bohlebots rpi cm4-carrier without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Raspberry Pi firmware against it before you order a PCB.
Similar boards
Raspberry Pi
Open source rover
nasa-jpl
220 × 178 mm144 parts2LApache-2.09.7kRaspberry Pi
Iot
dotnet
56 × 65 mm24 parts2LMIT2.4kRaspberry Pi
SPIRIT
SPIRIT-org
82 × 155 mm130 parts6LCERN-OHL-S-2.01.3kRaspberry Pi
CM5RevEng
schlae
55 × 40 mm417 parts10LNo license1.0kRaspberry Pi
Haxo hw
cardonabits
102.4 × 211.3 mm38 parts2LCustom license673Raspberry Pi
Phased
Neumi
75 × 100 mm71 parts2LNo license507