Sardisp
thaolt·sardisp·hardware/SARDISP.kicad_pcb
About the Sardisp PCB
Sardisp is an open source AVR/Arduino PCB design by thaolt, published on GitHub under the MIT license. It is a 2-layer board measuring 68.6 × 27.9 mm, with 18 components from 13 distinct parts.
Its main chip is the ATmega328P-PU, from the AVR/Arduino family. By type, the board carries 6 resistors, 4 diodes, 4 capacitors, 2 connectors, 1 IC and 1 crystal.
It belongs with the usb & debug tools designs in this gallery.
From the project
DIY Simple Arduino In-System-Programmer (Perf board USBasp clone)
What is it? Installation + Windows + Linux How to use + avrdude + AVRDUDESS + Arduino IDE Tools Schematic Perf-board implement * References
DIY Simple Arduino In-System-Programmer (aka perf-board USBasp clone)
https://zadig.akeo.ie/ https://electronics.stackexchange.com/questions/416714/avrdude-does-not-recognize-usbasp-device/417509#417509
https://raw.githubusercontent.com/thaolt/sardisp/master/drivers/usbasp_signed.zip

Main components on the Sardisp
Sardisp bill of materials (BOM)
18 components, 13 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ATmega328P-PU | DIP-28_W7.62mm | U1 |
| 1 | 12MHz | Crystal_HC18-U_Vertical | Y1 |
| 1 | ISPHeader | IDC-Header_2x05_P2.54mm_Horizontal | J1 |
| 1 | USB_B | USB_A_Stewart_SS-52100-001_Horizontal | J2 |
| 1 | Busy | LED_D3.0mm | D1 |
| 1 | Power | LED_D3.0mm | D2 |
| 2 | 3V6 | D_A-405_P7.62mm_Horizontal | D3, D4 |
| 1 | 0.1uF | C_Disc_D3.0mm_W1.6mm_P2.50mm | C1 |
| 2 | 22pF | C_Disc_D3.0mm_W1.6mm_P2.50mm | C2, C3 |
| 1 | 100uF | CP_Radial_D5.0mm_P2.50mm | C4 |
| 1 | 10K | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1 |
| 3 | 1K5 | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R2, R5, R6 |
| 2 | 68 | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R3, R4 |
Sardisp design files
The KiCad project lives in the thaolt/sardisp repository on GitHub; these links point at the commit this page was built from.
Sardisp: common questions
What microcontroller does the Sardisp use?
The Sardisp is built around the ATmega328P-PU, from the AVR/Arduino family.
How big is the Sardisp PCB?
The Sardisp measures 68.6 × 27.9 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Sardisp?
18 components, from 13 distinct parts. The full bill of materials is listed on this page.
Where can I download the Sardisp design files?
From the thaolt/sardisp repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Sardisp design in my own project?
Yes, under the terms of its MIT license, which thaolt chose for the repository.
Can I test firmware for the Sardisp without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k