Water meter counter

usimd·water-meter-counter

Water meter counter PCB layout, top view — open source PIC board by usimd

About the Water meter counter PCB

Water meter counter is an open source PIC PCB design by usimd, published on GitHub. It is a 2-layer board measuring 62.8 × 38.4 mm, with 26 components from 14 distinct parts.

Its main chip is the PIC18F25K80-I/MM, from the PIC family. Other key parts include the HCPL-817-30DE. By type, the board carries 11 resistors, 7 capacitors, 3 diodes, 2 ICs, 2 inductors and 1 connector.

From the project

Inductive water meter counting module for B-meters GSD8

This is a custom water meter counter project to get an interface to analog water meter readings for subsequent usage in Homeassistant. The project is outputting its readings via a generic S0 interface, though, to enable other use cases as well.

It features a custom 3D-printable model to snap on to the GSB-8 meter that houses the PCB. The software doing the actual work is located in the firmware folder. Since it is based on a Microchip PIC controller, it requires the respective infrastructure to build.

Water meter counter, from the project README
From the project README

Main components on the Water meter counter

PIC18F25K80-I/MMHCPL-817-30DE

Water meter counter bill of materials (BOM)

26 components, 14 distinct parts.

QtyPartRefs
1
PIC18F25K80-I/MM
PIC18F25K80_IML
Microchip
U1
1
HCPL-817-30DE
Broadcom
U2
1
S4B-XH-A(LF)(SN)
Conn_01x04
JST
J1
1
B5819W
MDD (Microdiode Semiconductor)
D1
2
SS14MH
SS14
Taiwan Semiconductor
D2, D3
2
05HCP-471K-51
470uH
Fastron
L1, L2
2
06035C104JAT2A
0.1uF
KYOCERA AVX
C1, C2
1
GRM188R61E106KA73D
10uF
Murata
C3
2
C0603C101J5GACTU
100pF
KEMET
C4, C5
2
C0603C222J5GACTU
2.2nF
KEMET
C6, C7
1
ESR03EZPJ103
10k
ROHM
R1
5
RC0603FR-07470RL
470
YAGEO
R2, R6, R7, R10, R11
1
RC0805FR-07220RL
220
YAGEO
R3
4
RC0603FR-07330KL
330k
YAGEO
R4, R5, R8, R9

Water meter counter design files

The KiCad project lives in the usimd/water-meter-counter repository on GitHub; these links point at the commit this page was built from.

Water meter counter: common questions

What microcontroller does the Water meter counter use?

The Water meter counter is built around the PIC18F25K80-I/MM, from the PIC family.

How big is the Water meter counter PCB?

The Water meter counter measures 62.8 × 38.4 mm, has 2 copper layers and is 1.579 mm thick.

How many components are on the Water meter counter?

26 components, from 14 distinct parts. The full bill of materials is listed on this page.

Where can I download the Water meter counter design files?

From the usimd/water-meter-counter repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Water meter counter design in my own project?

The repository has no license, so all rights stay with usimd. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Water meter counter without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug PIC firmware against it before you order a PCB.

Similar boards