Swipe stack hub
vclagudu·SWIPE-STACK·PCB/swipe-stack-hub/swipe-stack-hub/swipe-stack-hub.kicad_pcb
About the Swipe stack hub PCB
Swipe stack hub is an open source STM32 PCB design by vclagudu, published on GitHub. It is a 2-layer board measuring 109.2 × 71.4 mm, with 65 components from 40 distinct parts.
Its main chip is the STM32F091RCTx, from the STM32 family. Other key parts include the LMR51430 (LMR54410), HM19R, HM19L, MAX7375AXR805 and LM386. By type, the board carries 17 resistors, 13 capacitors, 9 connectors, 6 ICs, 5 switches and 3 LEDs.
From the project
Senior Design Projrct
Main components on the Swipe stack hub
Swipe stack hub bill of materials (BOM)
65 components, 40 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32F091RCTx | LQFP-64_10x10mm_P0.5mm | U1 |
| 1 | LMR51430 (LMR54410) | SOT-23-6 | U2 |
| 1 | HM19R | HM-19-MODULE | U3 |
| 1 | HM19L | HM-19-MODULE | U4 |
| 1 | MAX7375AXR805 | SOT-323_SC-70_Handsoldering | U5 |
| 1 | LM386 | SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mm | U6 |
| 1 | Barrel_Jack_Switch | BarrelJack_CUI_PJ-036AH-SMT_Horizontal | J1 |
| 1 | Conn_02x08_Odd_Even | IDC-Header_2x08_P2.54mm_Vertical_SMD | J2 |
| 1 | Conn_02x05_Odd_Even | IDC-Header_2x05_P2.54mm_Vertical | J3 |
| 1 | Conn_01x06 | JST_VH_B6P-VH-B_1x06_P3.96mm_Vertical | J4 |
| 1 | Conn_01x04 | JST_VH_B4P-VH-B_1x04_P3.96mm_Vertical | J5 |
| 4 | Conn_01x01_Socket | PinSocket_1x01_P2.54mm_Vertical | J6, J7, J8, J9 |
| 2 | 0.1uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | Cboot1, Cin2 |
| 1 | 2.2uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | Cin1 |
| 1 | 22uF | CP_Radial_D5.0mm_P2.50mm | Cout1 |
| 1 | Speaker | JST_VH_B2P-VH-FB-B_1x02_P3.96mm_Vertical | LS1 |
| 1 | R_Potentiometer | Potentiometer_Bourns_PTV09A-1_Single_Vertical | RVe1 |
| 1 | 22.1k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | Rfbb1 |
| 1 | 69.8k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | Rfbt1 |
| 3 | ~ | SW_SPST_PTS645 | SW1, SW2, SW3 |
Show 20 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | SW_Push | SW_SPST_PTS645 | SW4, SW5 |
| 1 | LED_Yellow | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | LD1 |
| 1 | LED_Green | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | LD2 |
| 1 | LED_Red | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | LD3 |
| 2 | LED1 | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1, D2 |
| 1 | Ferrite Bead | L_0805_2012Metric_Pad1.15x1.40mm_HandSolder | FB1 |
| 1 | 10uH | L_0805_2012Metric_Pad1.15x1.40mm_HandSolder | L1 |
| 2 | 10uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C3 |
| 3 | 0.1uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C4, C6 |
| 5 | .1uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C5, C7, C8, C9, C10 |
| 1 | 250uF | CP_Radial_D14.0mm_P5.00mm | C11 |
| 1 | .05uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C12 |
| 1 | 470uF | CP_Radial_D14.0mm_P5.00mm | C13 |
| 8 | 1k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2, R4, R5, R7, R10, R12, R13 |
| 2 | 470 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R6 |
| 2 | 100k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R8, R9 |
| 1 | 2k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R11 |
| 1 | 10 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R14 |
| 1 | 0 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R15 |
| 2 | R_Pack08 | SOIC127P762X240-16N | RN1, RN2 |
Swipe stack hub design files
The KiCad project lives in the vclagudu/SWIPE-STACK repository on GitHub; these links point at the commit this page was built from.
Swipe stack hub: common questions
What microcontroller does the Swipe stack hub use?
The Swipe stack hub is built around the STM32F091RCTx, from the STM32 family.
How big is the Swipe stack hub PCB?
The Swipe stack hub measures 109.2 × 71.4 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Swipe stack hub?
65 components, from 40 distinct parts. The full bill of materials is listed on this page.
Where can I download the Swipe stack hub design files?
From the vclagudu/SWIPE-STACK repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Swipe stack hub design in my own project?
The repository has no license, so all rights stay with vclagudu. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Swipe stack hub without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in SWIPE-STACK
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k