Nitrokey pro hardware
About the Nitrokey pro hardware PCB
Nitrokey pro hardware is an open source PCB design by vinaebizs, published on GitHub. It is a 2-layer board measuring 26 × 42 mm, with 10 components from 9 distinct parts.
By type, the board carries 8 connectors and 2 resistors.
It belongs with the usb & debug tools designs in this gallery.
From the project
J8 and J9 are different types of pads used on different target PCBs. They are all connected together to make testing easier.
J8 and J9 are different types of pads used on different target PCBs. They are all connected together to make testing easier.
R1 and R2 are required depending on whether you use Versaloon or ST-Link programmer.
R1 is used to power the target device when using ST-Link. ST-Link doesn't provide power to the target board normally, but it has 3.3V on pin 19 of the JTAG connector (which is normally not connected on the target board).
Nitrokey pro hardware bill of materials (BOM)
10 components, 9 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | WM9364 HEADER_6 | POGO6-oval | J1 |
| 1 | WM3983 USB_A | vasch_strip_10x2 | J2 |
| 1 | — | pin_strip_4 | J3 |
| 1 | HEADER_4 | SIL-2-2-guiding_holes | J4 |
| 1 | HEADER_6 | POGO6-oval-offset | J6 |
| 1 | HEADER_4 | SIL-2-2-guiding_holes-offest | J7 |
| 1 | HEADER_4 | SIL-2-2-drilled-guiding_holes | J8 |
| 1 | HEADER_4 | SIL-2-2-drilled-guiding_holes-offset | J9 |
| 2 | 510 0 | r_0805 | R1, R2 |
Nitrokey pro hardware design files
The KiCad project lives in the vinaebizs/nitrokey-pro-hardware repository on GitHub; these links point at the commit this page was built from.
Nitrokey pro hardware: common questions
How big is the Nitrokey pro hardware PCB?
The Nitrokey pro hardware measures 26 × 42 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Nitrokey pro hardware?
10 components, from 9 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Nitrokey pro hardware design files?
From the vinaebizs/nitrokey-pro-hardware repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Nitrokey pro hardware design in my own project?
The repository has no license, so all rights stay with vinaebizs. Use it as a reference, and ask the author before reusing the design.
Similar boards
XG Station Power
osy
54.3 × 91 mm9 parts2LCC-BY-4.0703
USB Hub Test
50 × 50 mm85 parts4LCC-BY-4.0703
FW-EC-DongleHiderPlus
LeoDJ
28.2 × 26.1 mm14 parts4LCERN-OHL-W-2.0490
Adapter tsop48
bbogush
48 × 33 mm3 parts2LGPL-3.0389
Adapter tsop48 solder
48 × 33 mm3 parts2LGPL-3.0389
Adapter soic8 solder
48 × 20 mm3 parts2LGPL-3.0389