Floppy Voltmeter Clock
virgoss·Floppy_Voltmeter_Clock·HARDWARE/Floppy voltmeter clock/Floppy voltmeter clock.kicad_pcb
About the Floppy Voltmeter Clock PCB
Floppy Voltmeter Clock is an open source STM32 PCB design by virgoss, published on GitHub under the CERN-OHL-S-2.0 license. It is a 2-layer board measuring 43 × 72 mm, with 32 components from 21 distinct parts.
Its main chip is the STM32G030F6PX, from the STM32 family. Other key parts include the H7233-1 and DS3231M. By type, the board carries 8 capacitors, 7 connectors, 7 resistors, 3 ICs, 3 switches and 2 diodes.
Main components on the Floppy Voltmeter Clock
Floppy Voltmeter Clock bill of materials (BOM)
32 components, 21 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32G030F6PX STM32G030F6Px | TSSOP-20_4.4x6.5mm_P0.65mm | U1 |
| 1 | H7233-1 | SOT-23 | U2 |
| 1 | DS3231M | SOIC-16W_7.5x10.3mm_P1.27mm | U3 |
| 1 | BUTTONS | JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J1 |
| 1 | C2927027 ~ | USB-C (only power) | J2 |
| 1 | BUTTONS IN BOARD | JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J3 |
| 1 | hours | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J4 |
| 1 | minutes | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J5 |
| 1 | seconds | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J6 |
| 1 | ST-Link | PinHeader_1x03_P2.54mm_Vertical | J7 |
| 1 | C70377 Q&J CR2032-BS-6-1 | BatteryHolder_Keystone_1060_1x2032 | BT1 |
| 1 | RESET_B | SMD BUTTON 5.1x5.1 | SW1 |
| 1 | MINUTES | SMD BUTTON 5.1x5.1 | SW2 |
| 1 | HOURS | SMD BUTTON 5.1x5.1 | SW3 |
| 1 | VAL** | mouse-bite-3mm-slot | mouse-bite-3mm-slot |
| 1 | 3V3_POWER_LED | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1 |
| 1 | LED_ALIVE | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D2 |
| 4 | 4.7UF 4.7uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C3, C6, C7 |
| 4 | 100NF 100nF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C4, C5, C8 |
| 6 | 5.1K 5.1k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2, R3, R5, R6, R7 |
Show 1 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 15K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4 |
Floppy Voltmeter Clock design files
The KiCad project lives in the virgoss/Floppy_Voltmeter_Clock repository on GitHub; these links point at the commit this page was built from.
Floppy Voltmeter Clock: common questions
What microcontroller does the Floppy Voltmeter Clock use?
The Floppy Voltmeter Clock is built around the STM32G030F6PX, from the STM32 family.
How big is the Floppy Voltmeter Clock PCB?
The Floppy Voltmeter Clock measures 43 × 72 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Floppy Voltmeter Clock?
32 components, from 21 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Floppy Voltmeter Clock design files?
From the virgoss/Floppy_Voltmeter_Clock repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Floppy Voltmeter Clock design in my own project?
Yes, under the terms of its CERN-OHL-S-2.0 license, which virgoss chose for the repository.
Can I test firmware for the Floppy Voltmeter Clock without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k