Controller f407

wa1hco·rotator_controller·hardware/controller-f407/controller-f407.kicad_pcb

Controller f407 PCB layout, top view — open source STM32 board by wa1hco

About the Controller f407 PCB

Controller f407 is an open source STM32 PCB design by wa1hco, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 159 × 99 mm, with 120 components from 43 distinct parts.

Its main chip is the STM32G431RBTx, from the STM32 family. Other key parts include the LITEON LTV-814S-TA1 and onsemi MOC3023SM. By type, the board carries 47 resistors, 25 diodes, 20 capacitors, 8 ICs, 7 transistors and 5 connectors.

From the project

Clean slate rebuild of full featured rotator controller.

This is the new controller, started from the outside in. The rotor interface and the AC motor drive are on rotordrive`. The Drive MCU and the analog front end are the next two sheets.

The directory is hardware/controller-f407/ because ADR 0014 names the STM32F407, and the tree sits beside the imported V4 project at hardware/controller/ without mixing files. Leave hardware/controller/ untouched. It is the reference for the V4 TVS, snubber, and connector practice.

Main components on the Controller f407

LITEON LTV-814S-TA1onsemi MOC3023SMSTM32G431RBTx

Controller f407 bill of materials (BOM)

120 components, 43 distinct parts.

QtyPartRefs
4
LITEON LTV-814S-TA1
LTV-814S-TA1
U1, U3, U5, U7
3
onsemi MOC3023SM
MOC3023SM
U2, U4, U6
1
STM32G431RBTx
U8
1
AOS AO3400A
AO3400A
Q1
3
ST BTA16-600SWRG
BTA16-600SWRG
Q2, Q4, Q6
3
JSCJ 2N7002
2N7002
Q3, Q5, Q7
1
pigtail to Anderson Powerpole 15/30/45, grey + black (V2). Housings TBD.
AC_PIGTAIL
J1
1
Phoenix 1757307 MSTBA 2,5/8-G-5,08
CDE_1to8
J2
1
SWD
J3
1
UART
J4
1
EL_POT
J5
1
cartridge T6.3A 250 V slow-blow in 5x20 clips (Keystone 3512 class)
T6.3A
F1
1
Omron G5LE-1A4-DC5
G5LE-1A4-DC5
K1
1
14 mm disc, 35 VAC continuous class (14D560K or equivalent)
35VAC
RV1
1
YAE_CAP_A
SJ1
1
CDE_CAP_A
SJ2
1
CDE_CAP_B
SJ3
1
YAE_CAP_B
SJ4
1
Zeming ZMCT103C 1000:1 5 A
ZMCT103C
TR1
12
BAT54
D1, D2, D14, D15, D16, D17, D18, D20 +4
Show 23 more
QtyPartRefs
1
S1M or US1M, 1 A, >= 200 V SMA
S1M
D3
6
FOSAN SMAJ90CA
SMAJ90CA
D4, D8, D9, D10, D11, D12
1
1N4148W
D5
3
RED
D6, D7, D13
2
SMAJ90CA
D19, D22
3
100nF
C1, C2, C3
3
0.1 uF X2 275 VAC film, 15 mm pitch class
100nF
C4, C5, C8
1
KEMET R60EW61005000K
100uF
C6
1
TDK B32526T1336K000
33uF
C7
10
100n
C9, C11, C12, C13, C14, C16, C17, C18 +2
1
1u
C10
1
4.7u
C15
10
10k
R1, R4, R5, R15, R22, R29, R33, R36 +2
9
1k
R2, R11, R18, R25, R32, R35, R38, R41 +1
4
100k
R2G1, R3G1, R4G1, R8
1
100
R3
8
7.5k
R6, R7, R12, R14, R19, R21, R26, R28
3
100
R9, R16, R23
3
180
R10, R17, R24
3
68
R13, R20, R27
1
10
R30
4
330
R31, R34, R37, R40
1
39k
R43

Controller f407 design files

The KiCad project lives in the wa1hco/rotator_controller repository on GitHub; these links point at the commit this page was built from.

Controller f407: common questions

What microcontroller does the Controller f407 use?

The Controller f407 is built around the STM32G431RBTx, from the STM32 family.

How big is the Controller f407 PCB?

The Controller f407 measures 159 × 99 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Controller f407?

120 components, from 43 distinct parts. The full bill of materials is listed on this page.

Where can I download the Controller f407 design files?

From the wa1hco/rotator_controller repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Controller f407 design in my own project?

Yes, under the terms of its GPL-3.0 license, which wa1hco chose for the repository.

Can I test firmware for the Controller f407 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

More boards in rotator_controller

Similar boards