GNSS
Will946·GNSS·GNSSPCB/ZED-F9P.kicad_pcb
About the GNSS PCB
GNSS is an open source PCB design by Will946, published on GitHub under the MIT license. It is a 4-layer board measuring 52.1 × 61 mm, with 59 components from 31 distinct parts.
Other key parts include the 3.3V and ZED-F9P. By type, the board carries 25 resistors, 9 jumpers, 8 connectors, 7 capacitors, 5 diodes and 2 ICs.
It belongs with the rf & radio and dev boards & breakouts designs in this gallery.
From the project
u-blox ZED-F9P RTK GNSS breakout board with dual-band L1/L2 reception and centimeter-level positioning accuracy.
Board for an autonomous cart that follows the edge of a lawn and sprays weed killer along the border. Goal is centimeter level positioning using RTK corrections so the cart can hold a precise line along a mapped boundary. Prototyping this board is the only part of the project built so far.
Not currently in use on the cart. Prototyping this board cost way more than expected, and the rest of the cart, drive base, sprayer, controller, was never built as a result. Right now this is just the GNSS board sitting on its own.

Main components on the GNSS
GNSS bill of materials (BOM)
59 components, 31 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 3.3V | SOT23-5 | U2 |
| 1 | ZED-F9P | ZED-F9P | U3 |
| 1 | Radio | 1X06_NO_SILK | J1 |
| 2 | Qwiic Right Angle | 1X04_1MM_RA | J2, J4 |
| 1 | PTH | 1X04_NO_SILK | J3 |
| 1 | — | USB-C-16P | J5 |
| 1 | — | 1X06_NO_SILK | J6 |
| 1 | — | 1X09_NO_SILK | J7 |
| 1 | U.FL | U.FL | J13 |
| 1 | FRAME-LETTER | CREATIVE_COMMONS | FRAME1 |
| 3 | — | SMT-JUMPER_2_NC_TRACE_SILK | JP1, JP2, JP3 |
| 1 | — | SMT-JUMPER_2_NO_SILK | JP4 |
| 1 | — | SMT-JUMPER_3_2-NC_TRACE_SILK | JP5 |
| 4 | STAND-OFF | STAND-OFF | JP31, JP41, JP91, JP101 |
| 1 | RED | LED-0603 | LED2 |
| 1 | Yellow | LED-0603 | D1 |
| 1 | 0.5A/40V/420mV | SOD-323 | D2 |
| 1 | GREEN | LED-0603 | D3 |
| 1 | BLUE | LED-0603 | D4 |
| 1 | PRTR5V0U2F | SOT886 | D6 |
Show 11 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | FERRITE_BEAD-120_OHM-0402 | 0402 | FB1 |
| 1 | 47pF | 0603 | C1 |
| 4 | 1.0uF | 0603 | C2, C3, C4, C6 |
| 2 | 0.1uF | 0603 | C5, C7 |
| 5 | 1k | 0603 | R1, R5, R11, R12, R13 |
| 12 | 33 | 0603 | R2, R3, R4, R6, R18, R19, R20, R21 +4 |
| 2 | 2.2k | 0603 | R7, R8 |
| 2 | 27 | 0603 | R9, R10 |
| 1 | 10 | 0603 | R14 |
| 1 | 100k | 0603 | R15 |
| 2 | 5.1k | 0603 | R16, R17 |
GNSS design files
The KiCad project lives in the Will946/GNSS repository on GitHub; these links point at the commit this page was built from.
- LayoutGNSSPCB/ZED-F9P.kicad_pcb
- SchematicGNSSPCB/ZED-F9P.kicad_sch
GNSS: common questions
How big is the GNSS PCB?
The GNSS measures 52.1 × 61 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the GNSS?
59 components, from 31 distinct parts. The full bill of materials is listed on this page.
Where can I download the GNSS design files?
From the Will946/GNSS repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the GNSS design in my own project?
Yes, under the terms of its MIT license, which Will946 chose for the repository.
Similar boards
Breakout 112pin Connector
rusefi
174 × 58 mm39 parts2LGPL-3.01.2kEecv breakout
rusefi
140.8 × 53.7 mm9 parts4LGPL-3.01.2kBreakout 60pin EEC-IV
rusefi
139.7 × 62.2 mm15 parts2LGPL-3.01.2k134pin 7-967288-1
rusefi
139.7 × 73.7 mm38 parts2LGPL-3.01.2k88 Pin Vag Breakout
rusefi
142 × 58 mm91 parts2LGPL-3.01.2kRj45 breakout
rene-dev
15.2 × 53.8 mm3 parts2LGPL-3.0979