Spyderrobot

wooseongjung·spyderrobot·hardware/pcb/spyder-mcu-v1/spyder-mcu-v1.kicad_pcb

This repository ships a schematic but no board layout.

About the Spyderrobot PCB

Spyderrobot is an open source STM32 PCB design by wooseongjung, published on GitHub under the MIT license. It is a 4-layer board, with 96 components from 43 distinct parts.

Its main chip is the STM32F411RETx, from the STM32 family. Other key parts include the TPS5430DDA. By type, the board carries 21 capacitors, 11 test points, 4 resistors, 3 diodes, 3 inductors and 2 ICs.

It belongs with the robotics & motion and sensors designs in this gallery.

From the project

Quadruped robot performs spider motion using 12 servo motors, Rpi5, and several sensors

KiCad project for the custom STM32 MCU board.

Spec: ../../docs/04-pcb-design.md Bring-up checklist: ../../docs/09-test-and-validation.md

Main components on the Spyderrobot

Spyderrobot bill of materials (BOM)

96 components, 43 distinct parts.

QtyPartRefs
1
STM32F411RETx
U1
1
TPS5430DDA
U2
1
Q_PMOS_GSD
Q1
1
Crystal
Y1
1
Conn_01x06
J1
2
100nF
C_BOOT1, C_RST1
1
100uF
C_BULK1
1
150nF
C_FILT1
2
20pF
C_HSE1, C_HSE2
4
22uF
C_IN1, C_IN2, C_OUT1, C_OUT2
1
D_Schottky
D_CLAMP1
1
LED
D_PWR1
1
Polyfuse
F1
1
0
JP1
1
Conn_01x03
JP_BOOT1
4
0
JP_OPA1, JP_OPA2, JP_OPA3, JP_OPA4
3
Conn_01x04
J_HCSR04, J_I2C1, J_UART1
1
Conn_01x02
J_PI1
1
Conn_ARM_JTAG_SWD_10
J_SWD1
7
10k
R_ALERT1, R_FB1, R_FILT1, R_IMU_INT1, R_REF1, R_REF2, R_RST1
Show 23 more
QtyPartRefs
1
2k
R_ECHO_BOT1
1
1k
R_ECHO_TOP1
1
3.24k
R_FB2
4
470R
R_LED1, R_LED2, R_LED3, R_LED_PWR1
2
4.7k
R_SCL1, R_SDA1
1
20m
R_Shunt1
1
SW_Push
SW_RST1
11
TestPoint
TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8 +3
1
BME280
U_ENV1
2
PRTR5V0U2X
U_ESD1, U_ESD2
1
MPU-9250
U_IMU1
1
INA226
U_INA1
1
MCP1700x-300xxTT
U_LDO1
1
OPA333xxD
U_OPA1
3
LED
D1, D2, D3
2
FerriteBead
FB1, FB2
1
22uH
L1
15
100nF
C1, C4, C5, C6, C7, C10, C11, C12 +7
2
1uF
C2, C9
3
10uF
C3, C14, C21
1
4.7uF
C8
2
1k
R1_INV1, R1_NI1
2
30k
R2_INV1, R2_NI1

Spyderrobot design files

The KiCad project lives in the wooseongjung/spyderrobot repository on GitHub; these links point at the commit this page was built from.

Spyderrobot: common questions

What microcontroller does the Spyderrobot use?

The Spyderrobot is built around the STM32F411RETx, from the STM32 family.

How big is the Spyderrobot PCB?

The Spyderrobot has 4 copper layers and is 1.6062 mm thick.

How many components are on the Spyderrobot?

96 components, from 43 distinct parts. The full bill of materials is listed on this page.

Where can I download the Spyderrobot design files?

From the wooseongjung/spyderrobot repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Spyderrobot design in my own project?

Yes, under the terms of its MIT license, which wooseongjung chose for the repository.

Can I test firmware for the Spyderrobot without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards