MotorDriveForge
younlea·MotorDriveForge·dataset/opensource/flatmcu/design/flatmcu.kicad_pcb
About the MotorDriveForge PCB
MotorDriveForge is an open source STM32 PCB design by younlea, published on GitHub. It is a 4-layer board measuring 77.8 × 63.2 mm, with 115 components from 50 distinct parts.
Its main chip is the STM32G431CBTx, from the STM32 family. Other key parts include the AP1117-33, DRV8353RS and TPS563240. By type, the board carries 50 capacitors, 35 resistors, 8 transistors, 6 connectors, 4 ICs and 4 diodes.
It belongs with the robotics & motion and power & battery designs in this gallery.
From the project
STM32 motor driver generate agent
The controller is based on the STM32G473CB microcontroller from ST Microelectronics. It contains an ARM Cortex-M4 core at up to 170MHz. The three-phase bridge driver is the TI DRV8353RS, which also contains shunt resistor current sensors and a 95V buck regulator.
The MOSFETs in the three-phase bridge (Toshiba TPW4R50ANH) are dual-side cooling. There's a large metal pad on top of them. A heatsink should be attached there. The opposite side of the board is intended for soldering on the large battery and phase wires.

Main components on the MotorDriveForge
MotorDriveForge bill of materials (BOM)
115 components, 50 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AP1117-33 | SOT-223-3_TabPin2 | U2 |
| 1 | DRV8353RS | TI-RGZ-48-QFN | U3 |
| 1 | STM32G431CBTx | LQFP-48_7x7mm_P0.5mm | U4 |
| 1 | TPS563240 | SOT-23-6 | U5 |
| 6 | TPW4R50ANH | Toshiba_DSOP-Advance | Q1, Q2, Q3, Q4, Q5, Q6 |
| 2 | Q_NMOS_GSD | SOT-23 | Q7, Q8 |
| 1 | Hall | JST_XH_B6B-XH-A_1x06_P2.50mm_Vertical | J1 |
| 1 | USB_B_Micro | USB_Micro_B_Female_10118193-0001LF | J2 |
| 1 | Throttle | JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J3 |
| 1 | SW Debug | JST_SH_SM05B-SRSS-TB_1x05-1MP_P1.00mm_Horizontal | J7 |
| 1 | UART to HBD | JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J8 |
| 1 | UART to BMS | JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J9 |
| 1 | Thermistor | R_0603_1608Metric | TH1 |
| 3 | TestPoint | PinHeader_1x01_P1.00mm_Vertical | TP1, TP2, TP3 |
| 1 | PMEG4005 | SOT-23 | D1 |
| 1 | SS1H10-E3/61T | D_SMA | D2 |
| 1 | LED_Dual_AACC | LED_RGB_1210 | D3 |
| 1 | PMEG2020 | D_SOD-323F | D4 |
| 2 | BLM18AG601SN1D | R_0603_1608Metric | FB1, FB2 |
| 1 | 100u | NR6045 | L1 |
Show 30 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 1.5u | Bourns_SRN3015 | L2 |
| 12 | 100n | C_0603_1608Metric | C1, C6, C10, C19, C38, C39, C42, C43 +4 |
| 9 | 1n | C_0603_1608Metric | C2, C3, C4, C5, C7, C25, C31, C34 +1 |
| 1 | 1u | C_1210_3225Metric | C8 |
| 2 | 4.7u | C_1210_3225Metric | C9, C14 |
| 7 | 1u | C_0603_1608Metric | C11, C13, C16, C20, C22, C23, C45 |
| 1 | 10u | C_0603_1608Metric | C12 |
| 4 | 1u | C_1206_3216Metric | C15, C28, C33, C36 |
| 2 | 100n | C_0805_2012Metric | C17, C18 |
| 1 | 47n | C_0805_2012Metric | C21 |
| 3 | 10n | C_0603_1608Metric | C24, C40, C46 |
| 1 | 330p | C_0603_1608Metric | C26 |
| 1 | 47n | C_0603_1608Metric | C27 |
| 2 | 4.7u | C_0805_2012Metric | C29, C30 |
| 3 | 2.2n | C_0603_1608Metric | C32, C35, C37 |
| 1 | 4.7u | C_0603_1608Metric | C41 |
| 2 | 22 | R_0603_1608Metric | R1, R2 |
| 8 | 1k | R_0603_1608Metric | R3, R4, R5, R14, R21, R24, R27, R31 |
| 7 | 10k | R_0603_1608Metric | R6, R7, R8, R9, R11, R33, R35 |
| 1 | 4.99k | R_0603_1608Metric | R10 |
| 1 | DNP | R_0603_1608Metric | R12 |
| 1 | 0 | R_0603_1608Metric | R13 |
| 2 | 100k | R_0603_1608Metric | R15, R19 |
| 1 | 220k | R_0603_1608Metric | R16 |
| 1 | 8.2k | R_0603_1608Metric | R17 |
| 3 | 2.5m | R_2512_6332Metric | R18, R22, R28 |
| 2 | 4.02k | R_0603_1608Metric | R20, R25 |
| 3 | 22k | R_0603_1608Metric | R23, R26, R30 |
| 1 | 73.2k | R_0603_1608Metric | R29 |
| 2 | 330 | R_0603_1608Metric | R32, R34 |
MotorDriveForge design files
The KiCad project lives in the younlea/MotorDriveForge repository on GitHub; these links point at the commit this page was built from.
MotorDriveForge: common questions
What microcontroller does the MotorDriveForge use?
The MotorDriveForge is built around the STM32G431CBTx, from the STM32 family.
How big is the MotorDriveForge PCB?
The MotorDriveForge measures 77.8 × 63.2 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the MotorDriveForge?
115 components, from 50 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the MotorDriveForge design files?
From the younlea/MotorDriveForge repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the MotorDriveForge design in my own project?
The repository has no license, so all rights stay with younlea. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the MotorDriveForge without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k