ZTL-Badge-Hardware
ZTL-Space·ZTL-Badge-Hardware
About the ZTL-Badge-Hardware PCB
ZTL-Badge-Hardware is an open source AVR/Arduino PCB design by ZTL-Space, published on GitHub under the MIT license. It is a 2-layer board measuring 80 × 80 mm, with 15 components from 13 distinct parts.
Its main chip is the ATmega328P-P, from the AVR/Arduino family. By type, the board carries 5 capacitors, 3 switches, 2 connectors, 1 IC, 1 crystal and 1 battery holder.
It belongs with the wearables designs in this gallery.
Main components on the ZTL-Badge-Hardware
ZTL-Badge-Hardware bill of materials (BOM)
15 components, 13 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ATmega328P-P | DIP-28_W7.62mm | U1 |
| 1 | 8MHz | Crystal_HC49-4H_Vertical | Y1 |
| 1 | UART | PinHeader_1x06_P2.54mm_Horizontal | J1 |
| 1 | ISP | PinHeader_2x03_P2.54mm_Vertical | J2 |
| 1 | CR2032 | Knopfzellenclip_20mm | BT1 |
| 1 | Left Button | Kurzhubtaster | SW1 |
| 1 | Right Button | Kurzhubtaster | SW2 |
| 1 | Power Switch | ESP101 | SW3 |
| 1 | 1088BS | 1088BS | D1 |
| 2 | 100nF | C_Disc_D3.8mm_W2.6mm_P2.50mm | C1, C2 |
| 2 | 22pF | C_Disc_D3.8mm_W2.6mm_P2.50mm | C3, C4 |
| 1 | 100uF | CP_Radial_D5.0mm_P2.50mm | C5 |
| 1 | 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1 |
ZTL-Badge-Hardware design files
The KiCad project lives in the ZTL-Space/ZTL-Badge-Hardware repository on GitHub; these links point at the commit this page was built from.
- LayoutZTL-Badge-Hardware.kicad_pcb
- SchematicZTL-Badge-Hardware.kicad_sch
ZTL-Badge-Hardware: common questions
What microcontroller does the ZTL-Badge-Hardware use?
The ZTL-Badge-Hardware is built around the ATmega328P-P, from the AVR/Arduino family.
How big is the ZTL-Badge-Hardware PCB?
The ZTL-Badge-Hardware measures 80 × 80 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the ZTL-Badge-Hardware?
15 components, from 13 distinct parts. The full bill of materials is listed on this page.
Where can I download the ZTL-Badge-Hardware design files?
From the ZTL-Space/ZTL-Badge-Hardware repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the ZTL-Badge-Hardware design in my own project?
Yes, under the terms of its MIT license, which ZTL-Space chose for the repository.
Can I test firmware for the ZTL-Badge-Hardware without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k