HardLabs

ST-LINK-V2 1

zukki4123·yukuyuku_ST-LINKV2-1_ProgrammerV2

ST-LINK-V2 1 PCB layout, top view — open source STM32 board by zukki4123

About the ST-LINK-V2 1 PCB

ST-LINK-V2 1 is an open source STM32 PCB design by zukki4123, published on GitHub under the MIT license. It is a 2-layer board measuring 50 × 20 mm, with 36 components from 19 distinct parts.

Its main chip is the STM32F103CBTX, from the STM32 family. Other key parts include the AP7333-33SAG-7. By type, the board carries 17 resistors, 10 capacitors, 3 diodes, 2 ICs, 1 transistor and 1 crystal.

It belongs with the usb & debug tools designs in this gallery.

From the project

回路をより改良したものです。

Main components on the ST-LINK-V2 1

AP7333-33SAG-7STM32F103CBTX

ST-LINK-V2 1 bill of materials (BOM)

36 components, 19 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
AP7333-33SAG-7
IC1
1
STM32F103CBTX
STM32F103CBTx
U1
1
MMBT3904
Q1
1
8MHZ
8mHz
Y1
1
USB_C_RECEPTACLE_USB2.0_16P
USB_C_Receptacle_USB2.0_16P
J1
1
350MA
350mA
F1
3
LED
D1, D2, D3
5
0.1UF
0.1uF
C1, C5, C6, C8, C10
1
4.7UF
4.7uF
C2
2
1UF
1uF
C3, C4
2
18PF
18pF
C7, C9
6
10K
10k
R1, R2, R4, R5, R9, R17
1
100R
R3
2
5.1K
5.1k
R6, R7
1
1.5K
1.5k
R8
1
39K
39k
R10
1
100
R11
2
4.7K
4.7k
R12, R13
3
1k
R14, R15, R16

ST-LINK-V2 1 design files

The KiCad project lives in the zukki4123/yukuyuku_ST-LINKV2-1_ProgrammerV2 repository on GitHub; these links point at the commit this page was built from.

ST-LINK-V2 1: common questions

What microcontroller does the ST-LINK-V2 1 use?

The ST-LINK-V2 1 is built around the STM32F103CBTX, from the STM32 family.

How big is the ST-LINK-V2 1 PCB?

The ST-LINK-V2 1 measures 50 × 20 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the ST-LINK-V2 1?

36 components, from 19 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the ST-LINK-V2 1 design files?

From the zukki4123/yukuyuku_ST-LINKV2-1_ProgrammerV2 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the ST-LINK-V2 1 design in my own project?

Yes, under the terms of its MIT license, which zukki4123 chose for the repository.

Can I test firmware for the ST-LINK-V2 1 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards