6 open source boards using the AP7333-33SAG-7
Real designs built with the AP7333-33SAG-7, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
EUB-04 Emiuet
emnyeca
297 × 102.4 mm251 parts2LNo license2Lora tracker
tiborkiss
77 × 74 mm103 parts4LMIT1Nordic nRF
NRF52832
jmos1
29.2 × 65.3 mm43 parts4LNo license0STM32
ST-LINK-V2 1
zukki4123
50 × 20 mm36 parts2LMIT0Yukuyuku UART ProgrammerV1
zukki4123
30 × 20 mm18 parts2LMIT0Yukuyuku UDPI ProgrammerV1
zukki4123
30 × 20 mm18 parts2LMIT0
How designs wire the AP7333-33SAG-7
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the AP7333-33SAG-7 connects to, and the resistors, capacitors and other passives placed on it.
- The OUT pin is tied to 3.3V on 6 of 6 designs.
- The IN pin is tied to 5V on 5 of 6 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| INpin 1 | Connected to: 5V 83% · GND 17% | — |
| OUTpin 2 | Connected to: 3.3V 100% | — |
| GNDpin 3 | Connected to: GND 83% · REG_IN 17% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include EUB-04 Emiuet by emnyeca, Lora tracker kicad by tiborkiss, NRF52832 by jmos1 and ST-LINK-V2 1 by zukki4123.
The AP7333-33SAG-7 in open source designs
The gallery holds 6 open source boards using the AP7333-33SAG-7 from 6 GitHub repositories; a typical one measures about 40 × 42.6 mm and carries around 40 components.
67% are two-layer designs, the rest use four layers or more, and 67% carry an open source license.
The most starred is EUB-04 Emiuet by emnyeca.
Microcontrollers on boards using the AP7333-33SAG-7
What boards using the AP7333-33SAG-7 are built for
AP7333-33SAG-7: common questions
Where can I find a AP7333-33SAG-7 reference design?
Each of the 6 boards on this page is a real design using the AP7333-33SAG-7. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the AP7333-33SAG-7 OUT pin connected?
The OUT pin is tied to 3.3V on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the AP7333-33SAG-7.
How is the AP7333-33SAG-7 IN pin connected?
The IN pin is tied to 5V on 5 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the AP7333-33SAG-7.
Which microcontrollers do boards using the AP7333-33SAG-7 use?
Most are built on ESP32 (1), Nordic nRF (1) and STM32 (1).
How big is a typical board using the AP7333-33SAG-7?
The median is 40 × 42.6 mm, and 67% are two-layer designs.
What is the most popular open source board using the AP7333-33SAG-7?
By GitHub stars, EUB-04 Emiuet by emnyeca, with 2 stars.
Can I simulate one of these boards using the AP7333-33SAG-7 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.