Atmega usbC programmer
06Felix06·atmega_usbC_programmer·hardware/Atmega_Programmer.kicad_pcb
About the Atmega usbC programmer PCB
Atmega usbC programmer is an open source AVR/Arduino PCB design by 06Felix06, published on GitHub under the CC-BY-NC-4.0 license. It is a 2-layer board measuring 57 × 25 mm, with 31 components from 21 distinct parts.
Its main chip is the ATMEGA328P-AU, from the AVR/Arduino family. Other key parts include the CH340C. By type, the board carries 9 capacitors, 7 connectors, 7 resistors, 4 diodes, 2 ICs and 1 crystal.
It belongs with the usb & debug tools designs in this gallery.
From the project
USB-C programmer for bare ATmega boards (ATmega328P, ATmega2560, …) – burns the Arduino bootloader and uploads sketches through a single 2×4 header, so your own PCBs don’t need a USB chip.
A small USB-C tool for your own ATmega boards (ATmega328P, ATmega2560, ...). It burns the Arduino bootloader and uploads sketches through a single 2×4 pin header, so your PCBs don't need a USB chip.
If you design your own boards around a bare ATmega chip, for example the ATmega328P from the Arduino Uno/Nano or the ATmega2560 from the Arduino Mega, you normally have two annoying options:

Main components on the Atmega usbC programmer
Atmega usbC programmer bill of materials (BOM)
31 components, 21 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | CH340C | SOP-16_L10.0-W3.9-P1.27-LS6.0-BL | U1 |
| 1 | ATMEGA328P-AU | TQFP-32_L7.0-W7.0-P0.80-LS9.0-BL | U2 |
| 1 | CSTNE16M0V53Z000R0 | OSC-SMD_3P-L3.2-W1.3-P1.20-L | X1 |
| 1 | UPLOAD_OUT | PinSocket_2x04_P2.54mm_Vertical | J1 |
| 1 | Bootl/CodeUP | PinHeader_2x04_P2.54mm_Vertical | J2 |
| 1 | TX_Jumper | PinHeader_1x03_P2.54mm_Vertical | J3 |
| 1 | RX_Jumper | PinHeader_1x03_P2.54mm_Vertical | J4 |
| 1 | Reset_Jumper | PinHeader_1x03_P2.54mm_Vertical | J5 |
| 1 | RST_Jumper | PinHeader_1x03_P2.54mm_Vertical | J6 |
| 1 | USB_C_RECEPTACLE_USB2.0_14P USB_C_Receptacle_USB2.0_14P | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J7 |
| 1 | C2909692 LCSC: C2909692 | SW-SMD_4P-L6.2-W6.2-P4.50-LS8.6 | SW1 |
| 1 | RX_RD | LED_0805_2012Metric | D1 |
| 1 | TX_RD | LED_0805_2012Metric | D2 |
| 1 | PWR_GRN | LED_0805_2012Metric | D3 |
| 1 | TestLED | LED_0805_2012Metric | D4 |
| 4 | 100NF 100nF | C_0805_2012Metric | C1, C3, C4, C12 |
| 3 | 10µF | C_0805_2012Metric | C2, C6, C11 |
| 2 | 1µF | C_0805_2012Metric | C5, C9 |
| 2 | 5.1K 5.1k | R_0805_2012Metric | R1, R2 |
| 1 | 10K 10k | R_0805_2012Metric | R4 |
Show 1 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 4 | 1k | R_0805_2012Metric | R5, R6, R7, R8 |
Atmega usbC programmer design files
The KiCad project lives in the 06Felix06/atmega_usbC_programmer repository on GitHub; these links point at the commit this page was built from.
Atmega usbC programmer: common questions
What microcontroller does the Atmega usbC programmer use?
The Atmega usbC programmer is built around the ATMEGA328P-AU, from the AVR/Arduino family.
How big is the Atmega usbC programmer PCB?
The Atmega usbC programmer measures 57 × 25 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Atmega usbC programmer?
31 components, from 21 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Atmega usbC programmer design files?
From the 06Felix06/atmega_usbC_programmer repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Atmega usbC programmer design in my own project?
It is published under CC-BY-NC-4.0, which limits how it may be reused; read the license before building on it.
Can I test firmware for the Atmega usbC programmer without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k