Liion Cell Simulator

0hasant·Liion_Cell_Simulator·hardware/kicad/cell_test_bench.kicad_pcb

Liion Cell Simulator PCB layout, top view — open source board by 0hasant

About the Liion Cell Simulator PCB

Liion Cell Simulator is an open source PCB design by 0hasant, published on GitHub. It is a 2-layer board measuring 180 × 130 mm, with 129 components from 68 distinct parts.

Other key parts include the OPA2188AID, LM339N, LM393N and TL431ACLPR. By type, the board carries 54 resistors, 22 connectors, 21 capacitors, 12 transistors, 8 ICs and 8 diodes.

It belongs with the power & battery designs in this gallery.

From the project

Single-cell characterization bench for 18650 and 21700 Li-ion cells (DMEGC INR45E, generic 3.5 Ah 18650). Part of the Solaris final-year project.

Single-cell characterization bench for 18650 and 21700 Li-ion cells (DMEGC INR45E, generic 3.5 Ah 18650). Part of the Solaris final-year project.

- 0–10 A linear electronic load (constant current), down to 2.0 V - Charging up to 5 A from a 30 V / 10 A bench PSU through an XL4016 CC/CV module, voltage set by a DAC - Bidirectional current measurement on one 10 mΩ 4-terminal shunt (Ohmite LVK25) - Cell held at about 10–45 °C in an insulated pocket cooled/heated by two TEC1-12706 Peltiers - STM32F103 Blue Pill, USB CDC to a Python UI - Hardware protection (OV, UV, OC, OT) that works without the…

Main components on the Liion Cell Simulator

OPA2188AIDLM339NLM393NTL431ACLPR

Liion Cell Simulator bill of materials (BOM)

129 components, 68 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
OPA2188AID
U301
1
MCP4725 module #1 (A0=GND, 0x60): VCC GND SCL SDA A0 OUT
U302
1
MCP4725 module #2 (A0=VCC, 0x61): VCC GND SCL SDA A0 OUT
U401
1
ADS1115 module #1 (ADDR=GND): VDD GND SCL SDA ADDR ALRT A0 A1 A2 A3
U501
1
ADS1115 module #2 (ADDR=VDD): VDD GND SCL SDA ADDR ALRT A0 A1 A2 A3
U502
1
LM339N
U601
1
LM393N
U602
1
TL431ACLPR
U603
10
BS170
Q201, Q202, Q203, Q204, Q205, Q206, Q302, Q303 +2
1
IRFP260NPBF
IRFP260N
Q301
1
IRLZ44NPBF
IRLZ44N
Q702
1
PSU in 30V 10A (+, -)
J101
1
12V buck XL4016: IN+ IN- OUT+ OUT-
J102
1
5V buck MP1584: IN+ IN- OUT+ OUT-
J103
1
Thermostat KSD9700 60C NC
J104
1
Cell power to pocket (+, -)
J205
1
Cell Kelvin sense (+, -)
J206
1
Series R 0.1R 50W alu (off-board)
J301
1
XL4016 CC/CV module: IN+ IN- OUT+ OUT-
J401
1
XL4016 FB tap (wire to FB pin, GND)
J402
Show 48 more
QtyPartRefs
1
NTC 10k cell
J501
1
NTC 10k air
J502
1
NTC 10k hs
J503
1
NTC 10k tec
J504
1
BTS7960 IBT-2 logic: RPWM LPWM R_EN L_EN R_IS L_IS VCC GND
J701
1
BTS7960 power: B+ B- M+ M-
J702
1
Peltier 2x TEC1-12706 in series
J703
1
Fan 12V heatsink (+,-)
J704
1
Pocket mixing fan 5V
J705
1
Fan 12V Peltier hot side (+,-)
J706
1
Blue Pill header A: B12 B13 B14 B15 A8 A9 A10 A11 A12 A15 B3 B4 B5 B6 B7 B8 B9 5V GND 3V3
J801
1
Blue Pill header B: VB C13 C14 C15 A0 A1 A2 A3 A4 A5 A6 A7 B0 B1 B10 B11 RST 3V3 GND GND
J802
1
Debug UART: TX RX GND
J803
1
Keystone 3568
10A mini blade
F101
1
Keystone 3568
15A mini blade (cell)
F202
1
ALFG2PF121
ALFG2PF121 (charge)
K1
1
ALFG2PF121
ALFG2PF121 (load)
K2
1
P6KE33A
P6KE33A (TVS)
D101
2
1N4007-E3/54
1N4007
D201, D202
3
BAT85,113
BAT85
D301, D302, D401
2
1N5819
D701, D801
1
100uF 50V
C101
2
220uF 25V
C102, C104
1
100uF 16V
C103
3
10NF
10nF
C301, C303, C507
1
1NF
1nF
C302
10
100NF
100nF
C304, C501, C502, C503, C504, C505, C506, C601 +2
2
10UF
10uF
C305, C801
1
1UF
1uF
C401
1
LVK25R010FER
10mR 1% 2W LVK25
R201
6
1k
R202, R205, R312, R313, R601, R701
7
100K
100k
R203, R204, R206, R207, R613, R702, R704
1
29.4k 0.1%
R301
2
1k 0.1%
R302, R309
8
10k 0.1%
R303, R304, R503, R504, R506, R507, R508, R509
11
10K
10k
R305, R306, R308, R510, R511, R602, R603, R609 +3
6
100R
R307, R402, R501, R502, R505, R703
1
12k 0.1%
R310
1
24.9K
24.9k
R311
1
1.2K
1.2k
R401
1
15K
15k
R604
1
8.2K
8.2k
R605
1
27K
27k
R606
1
9.1K
9.1k
R607
1
7.15K
7.15k
R608
1
5.6K
5.6k
R610
1
20K
20k
R612
2
4.7k DNP
R801, R802

Liion Cell Simulator design files

The KiCad project lives in the 0hasant/Liion_Cell_Simulator repository on GitHub; these links point at the commit this page was built from.

Liion Cell Simulator: common questions

How big is the Liion Cell Simulator PCB?

The Liion Cell Simulator measures 180 × 130 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Liion Cell Simulator?

129 components, from 68 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Liion Cell Simulator design files?

From the 0hasant/Liion_Cell_Simulator repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Liion Cell Simulator design in my own project?

The repository has no license, so all rights stay with 0hasant. Use it as a reference, and ask the author before reusing the design.

Similar boards