WifiKiwi
0xnullsect0r·WifiKiwi·hardware/kicad/WifiKiwi.kicad_pcb
About the WifiKiwi PCB
WifiKiwi is an open source ESP32 PCB design by 0xnullsect0r, published on GitHub under the GPL-3.0 license. It is a 4-layer board measuring 100 × 65 mm, with 1 components from 1 distinct parts.
Its main chip is the ESP32-C5-WROOM-1U-N8R8, from the ESP32 family.
From the project
KiCad 10.x hierarchical project. Open WifiKiwi.kicadpro` from the KiCad project manager.
KiCad 10.x hierarchical project. Open WifiKiwi.kicadpro` from the KiCad project manager.
The project opens cleanly in KiCad 10.0+ and exports to PDF / SVG. All 7 sub-sheets are present with their hierarchical pins defined and a netlist plan rendered as on-sheet text. The PCB has a 100 x 65 mm rectangular outline with four 1.6 mm mounting-hole pilots in the corners. No copper or footprints yet. kicad-cli sch erc reports ~150 violations, all "Pin not connected" on hierarchical sheet pins. This is expected: the sheets describe what needs to be wired; the actual symbol placement and wiring is…
Main components on the WifiKiwi
WifiKiwi bill of materials (BOM)
1 components, 1 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C5-WROOM-1U-N8R8 Espressif | U1 |
WifiKiwi design files
The KiCad project lives in the 0xnullsect0r/WifiKiwi repository on GitHub; these links point at the commit this page was built from.
WifiKiwi: common questions
What microcontroller does the WifiKiwi use?
The WifiKiwi is built around the ESP32-C5-WROOM-1U-N8R8, from the ESP32 family.
How big is the WifiKiwi PCB?
The WifiKiwi measures 100 × 65 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the WifiKiwi?
1 components, from 1 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the WifiKiwi design files?
From the 0xnullsect0r/WifiKiwi repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the WifiKiwi design in my own project?
Yes, under the terms of its GPL-3.0 license, which 0xnullsect0r chose for the repository.
Can I test firmware for the WifiKiwi without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k