E clutch controller with can

abdurrahman-eee·e-clutch-controller-with-can·hardware/eclutch_driver.kicad_pcb

E clutch controller with can PCB layout, top view — open source STM32 board by abdurrahman-eee

About the E clutch controller with can PCB

E clutch controller with can is an open source STM32 PCB design by abdurrahman-eee, published on GitHub. It is a 4-layer board measuring 140 × 95 mm, with 87 components from 55 distinct parts.

Its main chip is the STM32G431CBT6, from the STM32 family. Other key parts include the UCC27511ADBV, INA240A2PW gain 50, PWM rejection, TPS7B8133-Q1 40 V automotive LDO and SN65HVD230. By type, the board carries 31 capacitors, 28 resistors, 10 diodes, 5 ICs, 5 connectors and 4 transistors.

From the project

E-Clutch Actuator Driver — 12 V, 18 A peak / 4 A hold, STM32G431 + CAN

E-Clutch Actuator Driver — 12 V, 18 A peak / 4 A hold, STM32G431 + CAN

Drives a 0.34–0.5 Ω e-clutch actuator from a 12 V battery: 18 A for 2 s (pull-in), then 4 A continuous (hold), closed-loop current control, fast release, full diagnostics, CAN + discrete control.

To edit: clone the repo and open hardware/eclutchdriver.kicadpro in KiCad 10.

Gate drive: Q4 VGS 8.1–15 V (zener-clamped), Q2 VGS −7.1…−13 V. VBAT peak on release 18.3 V at 16 V input. Physical limit: 18 A × 0.5 Ω needs ≥ 9.6 V at the battery. Below that the firmware drives at 100 % and flags PULLINLIMITED`.

E clutch controller with can, from the project README
From the project README

Main components on the E clutch controller with can

UCC27511ADBVINA240A2PW gain 50, PWM rejectionTPS7B8133-Q1 40 V automotive LDOSTM32G431CBT6SN65HVD230

E clutch controller with can bill of materials (BOM)

87 components, 55 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
UCC27511ADBV
U1
1
INA240A2PW gain 50, PWM rejection
INA240A2PW
U2
1
TPS7B8133-Q1 40 V automotive LDO
TPS7B8133QDRVRQ1
U3
1
STM32G431CBT6
U4
1
SN65HVD230
U5
1
IPD90P04P4L-04 (-40 V, 4.1 mR) reverse-polarity
IPD90P04P4L-04
Q1
1
IPD90P04P4L-04 high-side enable
IPD90P04P4L-04
Q2
1
2N7002
Q3
1
IPD90N04S4-04 (40 V, 3.9 mR) PWM switch
IPD90N04S4-04
Q4
1
8MHZ
8MHz
Y1
1
BATTERY 12V
J1
1
E-CLUTCH
J2
1
SWD
J3
1
CAN / ENGAGE
J4
1
UART
J5
1
25A mini blade
F1
1
NCP18XH103F03RB (place at Q4/D5)
10k B3435
RT1
1
SMDJ26A (TVS 3 kW, 26 V)
SMDJ26A
D1
2
BZT52C15
D2, D3
1
STPS30L45CG fast-decay
STPS30L45CG
D4
Show 35 more
QtyPartRefs
1
STPS30L45CG slow-decay
STPS30L45CG
D5
1
SMAZ15
D6
1
GREEN 3V3
D7
1
GREEN status
D8
1
RED fault
D9
1
NUP2105L
D10
1
600R@100MHz
FB1
4
Panasonic EEH-ZA1V471P hybrid polymer
470uF 35V
C1, C2, C3, C4
4
10uF 50V
C5, C6, C7, C8
1
100nF 50V
C9
1
4.7nF 100V DNP
C10
1
10uF 25V
C11
1
1uF 25V
C12
9
100NF
100nF
C13, C15, C18, C21, C22, C23, C25, C27 +1
3
1NF
1nF
C14, C16, C17
1
1uF 50V
C19
2
4.7UF
4.7uF
C20, C24
1
1UF
1uF
C26
2
12PF
12pF
C28, C29
1
10NF
10nF
C30
9
10K
10k
R1, R9, R12, R16, R18, R20, R21, R23 +1
1
1k
R2
1
220R
R3
2
100R
R4, R14
4
100K
100k
R5, R15, R17, R19
1
Vishay WSK25122L000FEA (2 mR 1 % Kelvin)
2mR 3W
R6
1
4R7
R7
1
2R2
R8
1
10R DNP
R10
1
33R
R11
1
330R
R13
1
2K2
2k2
R22
2
1k
R24, R25
1
47K
47k
R26
1
120R
R29

E clutch controller with can design files

The KiCad project lives in the abdurrahman-eee/e-clutch-controller-with-can repository on GitHub; these links point at the commit this page was built from.

E clutch controller with can: common questions

What microcontroller does the E clutch controller with can use?

The E clutch controller with can is built around the STM32G431CBT6, from the STM32 family.

How big is the E clutch controller with can PCB?

The E clutch controller with can measures 140 × 95 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the E clutch controller with can?

87 components, from 55 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the E clutch controller with can design files?

From the abdurrahman-eee/e-clutch-controller-with-can repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the E clutch controller with can design in my own project?

The repository has no license, so all rights stay with abdurrahman-eee. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the E clutch controller with can without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards