31 open source boards using the STM32G431CBT6
Real designs built with the STM32G431CBT6, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
AxxSolder
AxxAxx
39 × 82.5 mm122 parts2LGPL-3.01.7kSTM32
Moco-RD501
ziteh
50 × 50 mm114 parts4LCERN-OHL-P-2.024STM32
Glove daq
corneliusgruss
46 × 56 mm63 parts2LMIT7STM32
Esc rev b
iamdarshg
173.8 × 282.9 mm687 parts4LNo license2STM32
Stm32-can ecu
dhruxraj
80 × 60 mm65 parts4LCERN-OHL-P-2.02STM32
Phase2-module
udaravima
130 × 90 mm172 parts4LGPL-3.01STM32
FOC Control Boards
coopjz
81 × 80.9 mm106 parts4LMIT1STM32
STM32G4-tutorial project
CanSource
147.4 × 140 mm57 parts2LCERN-OHL-P-2.01STM32
Stm32 audio class device
IsaacHo072
71.1 × 50.8 mm51 parts4LNo license1STM32
APX DEVBOARD
Gabouin
23.4 × 40.3 mm26 parts2LMIT1STM32
Bldc
kobertkirk
190 × 120 mm163 parts4LNo license0STM32
PCB-0018-A bldc motor driver
ihsan-sa
78 × 78 mm160 parts4LMIT0STM32
Tercio-B1
Kerol-Dev
46 × 46 mm139 parts6LApache-2.00STM32
Keeb4x4
TheRealBluesun
100 × 142.5 mm119 parts4LCERN-OHL-P-2.00STM32
Foc dev board
dganin-hw
108 × 81 mm109 parts4LNo license0STM32
E clutch controller with can
abdurrahman-eee
140 × 95 mm87 parts4LNo license0STM32
Expresso
amonbenson
85.3 × 75.7 mm84 parts4LMIT0STM32
CAN-BUS-FOC-Actuator
f1133
60 × 60 mm73 parts2LNo license0STM32
VibrationDamper
starline
80 × 55 mm66 parts2LMIT0STM32
MotorCAN
chairlesengi
60 × 60 mm65 parts4LMIT0- schematic only · 122 partsSTM32
Kicad skidl assignment
rajsrivastava9801-blip
122 partsNo license0 STM32
Moco-SC1
ziteh
40 × 40 mm102 parts4LCERN-OHL-P-2.024STM32
Esc rev b.before hand power replicate
iamdarshg
170 × 172.2 mm681 parts6LNo license2STM32
Phase1-module
udaravima
120 × 80 mm136 parts4LGPL-3.01STM32
MEMRICK V2
ub1qbm
40.1 × 50.9 mm33 parts2LNo license1STM32
ESC PCB V2
SurajShivakumar
48 × 58 mm76 parts4LNo license0STM32
Moco-OD501
ziteh
60 × 60 mm92 parts4LCERN-OHL-P-2.024STM32
Esc
iamdarshg
246 × 296 mm599 parts4LNo license2STM32
Moco pg4
ziteh
40 × 40 mm90 parts4LCERN-OHL-P-2.024STM32
Moco rc1
ziteh
35 × 35 mm80 parts4LCERN-OHL-P-2.024STM32
Moco-OI401
ziteh
40 × 40 mm65 parts2LCERN-OHL-P-2.024
How designs wire the STM32G431CBT6
Read from the KiCad layouts of 21 open source designs, one per repository: what each pin of the STM32G431CBT6 connects to, and the resistors, capacitors and other passives placed on it.
- The VDD pins have a decoupling capacitor on 20 of 21 designs, most often 100 nF (then 4.7 µF).
- The PG10 pin has a capacitor to GND on 19 of 21 designs, most often 100 nF.
- The VDDA pin has a decoupling capacitor on 18 of 21 designs, most often 100 nF (then 1 µF).
- The VBAT pin has a decoupling capacitor on 16 of 21 designs, most often 100 nF (then 4.7 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VBATpin 1 | Connected to: 3.3V 76% · a signal 19% |
|
| PC14pin 3 | Connected to: Not connected 76% · a signal 19% | — |
| PC15pin 4 | Connected to: Not connected 76% · a signal 19% | — |
| PF0pin 5 | Connected to: Signal 67% · not connected 33% |
|
| PF1pin 6 | Connected to: Signal 67% · not connected 33% |
|
| PG10pin 7 | Connected to: A connector 76% |
|
| PA0pin 8 | Connected to: Signal 86% |
|
| PA1pin 9 | Connected to: Signal 90% |
|
| PA2pin 10 | Connected to: A connector 24% |
|
| PA3pin 11 | Connected to: A connector 24% · not connected 19% |
|
| VSSApin 19 | Connected to: GND 90% | — |
| VREF+pin 20 | Connected to: 3.3V 71% · a signal 19% |
|
| VDDApin 21 | Connected to: 3.3V 71% · a signal 29% |
|
| VSSpin 23, 35, 47 | Connected to: GND 92% | — |
| VDDpin 24, 36, 48 | Connected to: 3.3V 89% |
|
| PA15pin 39 | Connected to: Signal 57% · not connected 43% |
|
| PB4pin 41 | Connected to: Signal 67% · not connected 29% |
|
| PB5pin 42 | Connected to: A connector 20% · not connected 20% |
|
| PB6pin 43 | Connected to: A connector 30% |
|
| PB7pin 44 | Connected to: A connector 25% · not connected 20% |
|
| PB8-BOOT0pin 45 | Connected to: Signal 90% |
|
23 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include AxxSolder by AxxAxx, Moco-OD501 by ziteh, Glove daq by corneliusgruss and Stm32-can ecu by dhruxraj.
The STM32G431CBT6 in open source designs
The gallery holds 31 open source boards using the STM32G431CBT6 from 23 GitHub repositories; a typical one measures about 74.6 × 60 mm and carries around 92 components.
73% use four copper layers or more, and 65% carry an open source license.
The most starred is AxxSolder by AxxAxx.
Parts used alongside the STM32G431CBT6
Microcontrollers on boards using the STM32G431CBT6
What boards using the STM32G431CBT6 are built for
STM32G431CBT6: common questions
Where can I find a STM32G431CBT6 reference design?
Each of the 31 boards on this page is a real design using the STM32G431CBT6. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the STM32G431CBT6 VDD pin?
The VDD pins have a decoupling capacitor on 20 of 21 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 21 open source designs using the STM32G431CBT6.
How is the STM32G431CBT6 PG10 pin connected?
The PG10 pin has a capacitor to GND on 19 of 21 designs, most often 100 nF. Counted from the KiCad layouts of 21 open source designs using the STM32G431CBT6.
What decoupling capacitors do designs use on the STM32G431CBT6 VDDA pin?
The VDDA pin has a decoupling capacitor on 18 of 21 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 21 open source designs using the STM32G431CBT6.
What parts are used alongside the STM32G431CBT6?
The AP2112K-3.3, AP2112K-3.3TRG1, USBLC6-2SC6, AMS1117-3.3 and BSC014N04LSATMA1 appear in the most repositories here.
Which microcontrollers do boards using the STM32G431CBT6 use?
Most are built on STM32 (31).
How big is a typical board using the STM32G431CBT6?
The median is 74.6 × 60 mm, and 27% are two-layer designs.
What is the most popular open source board using the STM32G431CBT6?
By GitHub stars, AxxSolder by AxxAxx, with 1,714 stars.
Can I simulate one of these boards using the STM32G431CBT6 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.