F.L.A.W.-D.C.
Adam-Primus·F.L.A.W.-D.C.·Kicad Files/Kicad Files.kicad_sch
About the F.L.A.W.-D.C. PCB
F.L.A.W.-D.C. is an open source ESP32 PCB design by Adam-Primus, published on GitHub under the MIT license. It is a board, with 6 components from 3 distinct parts.
Its main chip is the ESP32_30pin, from the ESP32 family. By type, the board carries 2 modules and 1 IC.
It belongs with the robotics & motion, iot & wireless and sensors designs in this gallery.
From the project
I am a beginner and this is my first project where I control a motors using an esp32 and motor driver so this will be a newer experience to me and additionally I still have to cover a large pile of knowledge on coding firmware so this project is a stepping stone for my future pro
I am a beginner and this is my first project where I control a motors using an esp32 and motor driver so this will be a newer experience to me and additionally I still have to cover a large pile of knowledge on coding firmware so this project is a stepping stone for my future projects.
https://github.com/Adam-Primus/F.L.A.W.-D.C./blob/main/BOM.csv
F.L.A.W.-D.C. bill of materials (BOM)
6 components, 3 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | — | ESP32_30pin | U1 |
| 2 | Motor | M1, M2 | |
| 3 | IR Sensor | IR-1, IR-2, IR-3 |
F.L.A.W.-D.C. design files
The KiCad project lives in the Adam-Primus/F.L.A.W.-D.C. repository on GitHub; these links point at the commit this page was built from.
- SchematicKicad Files/Kicad Files.kicad_sch
- BOMBOM.csv
F.L.A.W.-D.C.: common questions
What microcontroller does the F.L.A.W.-D.C. use?
The F.L.A.W.-D.C. is built around the ESP32_30pin, from the ESP32 family.
How many components are on the F.L.A.W.-D.C.?
6 components, from 3 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the F.L.A.W.-D.C. design files?
From the Adam-Primus/F.L.A.W.-D.C. repository on GitHub, which has the schematic and the BOM; the links under Design files point to each one.
Can I use the F.L.A.W.-D.C. design in my own project?
Yes, under the terms of its MIT license, which Adam-Primus chose for the repository.
Can I test firmware for the F.L.A.W.-D.C. without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k