Switchbox3
AgOpenGPS-Official·Rate_Control·SwitchBox/SwitchBox3/Switchbox3.kicad_pcb
About the Switchbox3 PCB
Switchbox3 is an open source AVR/Arduino PCB design by AgOpenGPS-Official, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 110 × 54 mm, with 24 components from 14 distinct parts.
Its main chip is the Arduino_Nano_v3.x, from the AVR/Arduino family. By type, the board carries 11 switches, 5 capacitors, 3 connectors, 2 resistors, 1 module and 1 diode.
It belongs with the robotics & motion designs in this gallery.
Main components on the Switchbox3
Switchbox3 bill of materials (BOM)
24 components, 14 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Arduino_Nano_v3.x | Arduino_Nano_outline | A1 |
| 1 | Power | TerminalBlock_Phoenix_PT-1,5-2-5.0-H_1x02_P5.00mm_Horizontal | J1 |
| 1 | CONN_02X02_COUNTER_CLOCKWISE Conn_01x15_Female | PinSocket_1x15_P2.54mm_Vertical | J2 |
| 1 | I2C-3V3 Conn_01x15_Female | PinSocket_1x15_P2.54mm_Vertical | J3 |
| 1 | mEZD71201A | mEZD71201A | RG1 |
| 2 | SW_SPDT | Mini_Toggle_3pin | SW1, SW2 |
| 9 | SW_SPST | Mini_Toggle_2pin | SW3, SW4, SW5, SW6, SW7, SW8, SW9, SW10 +1 |
| 1 | 1N5408 | 1N5408 | D1 |
| 1 | 22UF 1000uF | CP_Radial_D10.0mm_P5.00mm | C1 |
| 1 | 10UF 2.2uF | C_Disc_D5.0mm_W2.5mm_P2.50mm | C2 |
| 1 | 1UF 10uF | C_Disc_D5.0mm_W2.5mm_P2.50mm | C3 |
| 1 | 470UF 1000uF | CP_Radial_D10.0mm_P5.00mm | C4 |
| 1 | 330UF 0.1uf | C_Disc_D5.0mm_W2.5mm_P2.50mm | C5 |
| 2 | 270 10K | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R2 |
Switchbox3 design files
The KiCad project lives in the AgOpenGPS-Official/Rate_Control repository on GitHub; these links point at the commit this page was built from.
Switchbox3: common questions
What microcontroller does the Switchbox3 use?
The Switchbox3 is built around the Arduino_Nano_v3.x, from the AVR/Arduino family.
How big is the Switchbox3 PCB?
The Switchbox3 measures 110 × 54 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Switchbox3?
24 components, from 14 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Switchbox3 design files?
From the AgOpenGPS-Official/Rate_Control repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Switchbox3 design in my own project?
Yes, under the terms of its GPL-3.0 license, which AgOpenGPS-Official chose for the repository.
Can I test firmware for the Switchbox3 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in Rate_Control
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k