RC11-2

AgOpenGPS-Official·Rate_Control·Teensy/RC11-2/PCB/RC11.kicad_pcb

RC11-2 PCB layout, top view — open source NXP board by AgOpenGPS-Official

About the RC11-2 PCB

RC11-2 is an open source NXP PCB design by AgOpenGPS-Official, published on GitHub under the GPL-3.0 license. It is a 4-layer board measuring 159 × 130 mm, with 100 components from 52 distinct parts.

Its main chip is the Teensy_Ethernet, from the NXP family. Other key parts include the AZ1117CH-3.3TRG1, XL2596, C66405, ULN2803A and LM7805_TO220. By type, the board carries 20 resistors, 19 connectors, 18 diodes, 16 capacitors, 9 ICs and 8 relays.

It belongs with the robotics & motion designs in this gallery.

RC11-2, from the project README
From the project README

Main components on the RC11-2

RC11-2 bill of materials (BOM)

100 components, 52 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
AZ1117CH-3.3TRG1
AZ1117
IC1
1
XL2596
IC2
3
C66405
PC817 C66405
U1, U2, U6
1
ULN2803A
U3
1
LM7805_TO220
U4
1
MCP6002-XP
MCP6002-xP
U5
1
MCP2562-E-P
U8
1
Teensy_Ethernet
J1
1
CONN_02X02_COUNTER_CLOCKWISE
Conn_02x02_Counter_Clockwise
J2
1
I2C-3V3
J3
2
CONN_01X06_FEMALE
Conn_01x06_Female
J4, J15
4
CONN_01X08_FEMALE
Conn_01x08_Female
J5, J6, J7, J16
1
12V
J8
1
12V
J9
1
Ground
J10
1
Ground
J11
1
776087-1
776087-1-776087-1
J12
1
CONN_01X05
Conn_01x05
J13
1
HR915310A
J14
1
C2937625
Pressure
J17
Show 32 more
QtyPartRefs
1
C492401
Can Resistor
J18
1
C403774
Motor1 GRV
J21
2
C492610
F1, F2
8
C30431
Relay_SPDT
K1, K2, K3, K4, K5, K6, K7, K8
2
KF142V-5.0-4P
KF1, KF2
1
27K
RV1
1
C15771
PESD1CAN_215 C15771
S1
1
Pressure Ohms1
TP1
1
Pressure Ohms2
TP2
9
LED
D1, D3, D4, D5, D6, D7, D8, D9 +1
2
SS36
D2, D13
1
S10MC
D11
1
C727081
1N4007 C727081
D12
2
BAT42
D14, D15
3
C191023
1N5819 C191023
D16, D17, D18
2
SMDRI127-680MT
L1, L2
1
22UF
22uF
C1
1
10UF
10uF
C2
2
1UF
1uF
C3, C12
4
470UF
470uF
C4, C7, C9, C10
1
330UF
330uF
C5
7
0.1UF
0.1uF
C6, C8, C11, C13, C14, C15, C16
3
270
R1, R2, R18
8
750
R3, R4, R5, R6, R7, R8, R9, R10
1
150
R11
2
2.2K
R12, R13
1
500
R14
1
470
R15
1
120
R16
1
2K
R17
1
5.2K
R19
1
1K
R20

RC11-2 design files

The KiCad project lives in the AgOpenGPS-Official/Rate_Control repository on GitHub; these links point at the commit this page was built from.

RC11-2: common questions

What microcontroller does the RC11-2 use?

The RC11-2 is built around the Teensy_Ethernet, from the NXP family.

How big is the RC11-2 PCB?

The RC11-2 measures 159 × 130 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the RC11-2?

100 components, from 52 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the RC11-2 design files?

From the AgOpenGPS-Official/Rate_Control repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the RC11-2 design in my own project?

Yes, under the terms of its GPL-3.0 license, which AgOpenGPS-Official chose for the repository.

Can I test firmware for the RC11-2 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug NXP firmware against it before you order a PCB.

More boards in Rate_Control

Similar boards