Fall-26-ESD-Project

agyei2352·Fall-26-ESD-Project·PCB Design/ESD_Wristband_Monitor.kicad_pcb

Fall-26-ESD-Project PCB layout, top view — open source Nordic nRF board by agyei2352

About the Fall-26-ESD-Project PCB

Fall-26-ESD-Project is an open source Nordic nRF PCB design by agyei2352, published on GitHub under the Custom license license. It is a 2-layer board measuring 32 × 40 mm, with 23 components from 13 distinct parts.

Its main chip is the nRF52840-QIAA, from the Nordic nRF family. By type, the board carries 14 capacitors, 3 resistors, 2 crystals, 2 inductors, 1 IC and 1 battery holder.

It belongs with the rf & radio designs in this gallery.

From the project

This directory contains the editable KiCad 10 project, manufacturing files, and 3D mechanical handoff models for the bare Nordic nRF52840-QIAA (aQFN-73) wearable ESD wristband monitor.

This directory contains the editable KiCad 10 project, manufacturing files, and 3D mechanical handoff models for the bare Nordic nRF52840-QIAA (aQFN-73) wearable ESD wristband monitor.

The design adheres strictly to Nordic Semiconductor nRF52840 Product Specification v1.11 / v1.12, Section 7.3 (Circuit Configuration No. 2 for QIAA aQFN-73):

1. Power Configuration (Normal Voltage Mode): - Supply: Single CR2032 primary coin cell ($3.0\text{ V}$ nominal, $1.7\text{--}3.6\text{ V}$ operational). - High-voltage regulator REG0 bypassed by shorting VDDH (Pin Y2) directly to VDD (Pins B1, W1, A22…

Fall-26-ESD-Project, from the project README
From the project README

Main components on the Fall-26-ESD-Project

Fall-26-ESD-Project bill of materials (BOM)

23 components, 13 distinct parts.

QtyPartRefs
1
nRF52840-QIAA
U1
1
32MHz
X1
1
32.768kHz
X2
1
CR2032
BT1
1
3.9nH
L1
1
10uH
L2
4
12pF
C1, C2, C14, C15
1
100pF
C3
1
1.0uF
C4
6
100nF
C5, C7, C8, C9, C10, C11
1
1.2pF
C12
1
1.5pF
C13
3
1.5k
R1, R2, R3

Fall-26-ESD-Project design files

The KiCad project lives in the agyei2352/Fall-26-ESD-Project repository on GitHub; these links point at the commit this page was built from.

Fall-26-ESD-Project: common questions

What microcontroller does the Fall-26-ESD-Project use?

The Fall-26-ESD-Project is built around the nRF52840-QIAA, from the Nordic nRF family.

How big is the Fall-26-ESD-Project PCB?

The Fall-26-ESD-Project measures 32 × 40 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Fall-26-ESD-Project?

23 components, from 13 distinct parts. The full bill of materials is listed on this page.

Where can I download the Fall-26-ESD-Project design files?

From the agyei2352/Fall-26-ESD-Project repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Fall-26-ESD-Project design in my own project?

It is published under Custom license, which limits how it may be reused; read the license before building on it.

Can I test firmware for the Fall-26-ESD-Project without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Nordic nRF firmware against it before you order a PCB.

Similar boards