I2c mux hat
amsterisk·i2c-mux-hat·hardware/i2c-mux-hat.kicad_pcb
About the I2c mux hat
I2c mux hat is an open source PCB design by amsterisk, published on GitHub under the CERN-OHL-S-2.0 license. It is a 2-layer board measuring 65 × 56 mm, with 68 components from 14 distinct parts.
Other key parts include the TCA9548APWR. By type, the board carries 22 resistors, 17 jumpers, 9 connectors, 8 fuses, 8 diodes and 2 capacitors.
It belongs with the dev boards & breakouts designs in this gallery.
From the project
Open-hardware 8-channel I2C multiplexer HAT (TCA9548A) for Raspberry Pi / Orange Pi / Banana Pi, with per-channel 3.3V/5V selection and RJ9 + 0.1in connectors. KiCad 9, CERN-OHL-S-2.0.
An open-hardware 8-channel I2C multiplexer board for single-board computers with a Raspberry Pi-compatible 40-pin header (Raspberry Pi, Orange Pi, Banana Pi, ...).
Status: work in progress — schematic done (ERC clean), PCB routed (DRC clean), not yet reviewed or fabricated.
- TCA9548A 8-channel I2C switch, address 0x70–0x77 (3-way DIP switch, default 0x70). - Per-channel voltage: a 3-pin jumper selects 3.3 V or 5 V for that channel's pull-ups and connector power. The mux runs at 3.3 V and translates levels, so 5 V devices never reach the host's GPIO. - Per-channel connector: keyed JST XH…
Main components on the I2c mux hat
I2c mux hat bill of materials (BOM)
68 components, 14 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TCA9548APWR | TSSOP-24_4.4x7.8mm_P0.65mm | U1 |
| 1 | 2x20 stacking header | PinSocket_2x20_P2.54mm_Vertical | J1 |
| 8 | JST XH 4p | JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J101, J201, J301, J401, J501, J601, J701, J801 |
| 8 | 100mA hold | Fuse_0805_2012Metric | F101, F201, F301, F401, F501, F601, F701, F801 |
| 1 | RST-GPIO4 | PinHeader_1x02_P2.54mm_Vertical | JP1 |
| 8 | VSEL | PinHeader_1x03_P2.54mm_Vertical | JP101, JP201, JP301, JP401, JP501, JP601, JP701, JP801 |
| 8 | PU_EN | PinHeader_1x02_P2.54mm_Vertical | JP102, JP202, JP302, JP402, JP502, JP602, JP702, JP802 |
| 1 | ADDR | SW_DIP_SPSTx03_Slide_KingTek_DSHP03TS_W7.62mm_P1.27mm | SW1 |
| 8 | USBLC6-2SC6 | SOT-23-6 | D101, D201, D301, D401, D501, D601, D701, D801 |
| 1 | 100n | C_0603_1608Metric | C1 |
| 1 | 1u | C_0603_1608Metric | C2 |
| 4 | 10k | R_0603_1608Metric | R1, R4, R5, R6 |
| 2 | 4.7k | R_0603_1608Metric | R2, R3 |
| 16 | 2.2k | R_0603_1608Metric | R101, R102, R201, R202, R301, R302, R401, R402 +8 |
I2c mux hat design files
The KiCad project lives in the amsterisk/i2c-mux-hat repository on GitHub; these links point at the commit this page was built from.
- Layouthardware/i2c-mux-hat.kicad_pcb
- Schematichardware/i2c-mux-hat.kicad_sch
I2c mux hat: common questions
How big is the I2c mux hat?
The I2c mux hat measures 65 × 56 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the I2c mux hat?
68 components, from 14 distinct parts. The full bill of materials is listed on this page.
Where can I download the I2c mux hat design files?
From the amsterisk/i2c-mux-hat repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the I2c mux hat design in my own project?
Yes, under the terms of its CERN-OHL-S-2.0 license, which amsterisk chose for the repository.
Similar boards
Breakout 112pin Connector
rusefi
174 × 58 mm39 parts2LGPL-3.01.2kEecv breakout
rusefi
140.8 × 53.7 mm9 parts4LGPL-3.01.2kBreakout 60pin EEC-IV
rusefi
139.7 × 62.2 mm15 parts2LGPL-3.01.2k134pin 7-967288-1
rusefi
139.7 × 73.7 mm38 parts2LGPL-3.01.2k88 Pin Vag Breakout
rusefi
142 × 58 mm91 parts2LGPL-3.01.2kRj45 breakout
rene-dev
15.2 × 53.8 mm3 parts2LGPL-3.0979