87 open source boards using the TCA9548APWR
Real designs built with the TCA9548APWR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Zero Palm V1
molanocortes
51.7 × 23.9 mm9 parts2LCustom license78Cellsim-8ch
atopile
13 × 9 mm608 parts4LMIT29AVR/Arduino
OpenHarrierUFC
OpenHarrier
144 × 158 mm91 parts2LGPL-3.013NXP
Sigyn
wimblerobotics
96.5 × 76.2 mm73 parts4LApache-2.07STM32
Glove daq
corneliusgruss
46 × 56 mm63 parts2LMIT7Raspberry Pi
Unfolding space hardware
jakobkilian
57 × 74.6 mm82 parts2LCC-BY-4.05Testolomew
Architeuthis-Flux
78.7 × 58.4 mm548 parts4LNo license3I2C multiplexer TCA9548A
SolderedElectronics
38 × 54 mm35 parts2LTAPR-OHL-1.03CyCompute
M2I-HABET
230 × 70 mm29 parts2LNo license3ESP32
EmbeddedKeyboard
01binary
143.2 × 105.8 mm108 parts4LNo license2ESP32
MIPI Robot Nextgen
hminhphi
76 × 52 mm51 parts2LNo license2AVR/Arduino
Mercury 2021
ksurct
100 × 100 mm40 parts2LApache-2.02- schematic only · 139 partsESP32
GrowHub
Ajakovski
139 partsMIT2 - schematic only · 110 partsRaspberry Pi
Smart chess
promaaa
110 partsMIT2 STM32
PCB AMR
ManuelOrtizCamacho
142.9 × 100.3 mm103 parts2LNo license1GQuintic-EEPROM-Header
synthetos
36.8 × 35.6 mm68 parts2LMIT1ESP32
RoboCore 2.0
AvishkaVishwa
83 × 58 mm64 parts2LNo license1STM32
Roly
szf2020
130 × 100 mm56 parts2LCC-BY-SA-4.01ESP32
Osmo pocket esp32-gimbal
SREESAIARJUN
26 × 85 mm53 parts4LNo license1Odonata
Stefanos0710
85.8 × 69.8 mm42 parts4LMIT1- schematic only · 67 partsESP32
Prosthetic
SoumyadeepXD
67 partsNo license1 - schematic only · 31 partsESP32
Urine analyzer lite
Sid93
31 parts2LNo license1 Raspberry Pi
Iasis
hydazz
130 × 100 mm636 parts6LApache-2.00NXP
TDAB
iowlabs
120 × 120 mm587 parts4LGPL-3.00STM32
SplitBoard8Voice
hsetlik
310 × 199 mm517 parts4LNo license0ESP32
Felső panel
NBence0
120.1 × 70.2 mm274 parts6LNo license0Airfoil
vmalarczyk
76.2 × 170.2 mm244 parts4LNo license0ESP32
C816SX
rjacobs1969
160 × 101.4 mm229 parts6LNo license0AVR/Arduino
Chessconnect
K-0hm
396.3 × 336.1 mm196 parts2LGPL-3.00Cm5-guard-A
Brico-Hams
290 × 280 mm157 parts2LNo license0Cm5-guard-A
anatolbricoham
290 × 280 mm157 parts2LNo license0ESP32
Board1 power
DashiellRussell
100 × 100 mm147 parts4LNo license0ESP32
Windsensor
kristofkatzenberger
70 × 70 mm123 parts4LMIT0V2
evolutek
70 × 130 mm121 parts2LNo license0STM32
Skadi 6 bay
M0RCHED
106 parts2LApache-2.00Prime Maxel v3
nagapi2357-ui
205 × 150 mm96 parts4LCC-BY-SA-4.00
How designs wire the TCA9548APWR
Read from the KiCad layouts of 61 open source designs, one per repository: what each pin of the TCA9548APWR connects to, and the resistors, capacitors and other passives placed on it.
- The SCL pin has a pull-up to 3.3V on 41 of 58 designs, most often 4.7 kΩ (then 10 kΩ).
- The SDA pin has a pull-up to 3.3V on 41 of 58 designs, most often 4.7 kΩ (then 10 kΩ).
- The A1 pin is tied to GND on 42 of 61 designs (a signal on 17).
- The VCC pin has a decoupling capacitor on 34 of 58 designs, most often 100 nF (then 10 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| A0pin 1 | Connected to: GND 64% · a signal 28% | — |
| A1pin 2 | Connected to: GND 69% · a signal 28% | — |
| RESETpin 3 | Connected to: A connector 23% |
|
| SD0pin 4 | Connected to: A connector 54% |
|
| SC0pin 5 | Connected to: A connector 52% |
|
| SD1pin 6 | Connected to: A connector 58% |
|
| SC1pin 7 | Connected to: A connector 58% |
|
| SD2pin 8 | Connected to: A connector 47% |
|
| SC2pin 9 | Connected to: A connector 49% |
|
| SD3pin 10 | Connected to: A connector 49% |
|
| SC3pin 11 | Connected to: A connector 49% |
|
| GNDpin 12 | Connected to: GND 93% | — |
| SD6pin 17 | Connected to: Not connected 63% · a signal 37% | — |
| SC6pin 18 | Connected to: Not connected 63% · a signal 37% | — |
| SD7pin 19 | Connected to: Not connected 62% · a signal 38% | — |
| SC7pin 20 | Connected to: Not connected 62% · a signal 38% | — |
| A2pin 21 | Connected to: GND 67% · a signal 28% | — |
| SCLpin 22 | Connected to: A connector 41%, the microcontroller 38% |
|
| SDApin 23 | Connected to: A connector 41%, the microcontroller 38% |
|
| VCCpin 24 | Connected to: 3.3V 83% · a signal 16% |
|
4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Encoder board by molanocortes, Cellsim-8ch by atopile, OpenHarrierUFC by OpenHarrier and Meshtonic h4m v2 by Josephrp.
The TCA9548APWR in open source designs
The gallery holds 87 open source boards using the TCA9548APWR from 72 GitHub repositories; a typical one measures about 94.7 × 76.2 mm and carries around 72 components.
67% are two-layer designs, the rest use four layers or more, and 31% carry an open source license.
The most starred is Zero Palm V1 by molanocortes.
Parts used alongside the TCA9548APWR
Microcontrollers on boards using the TCA9548APWR
What boards using the TCA9548APWR are built for
TCA9548APWR: common questions
Where can I find a TCA9548APWR reference design?
Each of the 87 boards on this page is a real design using the TCA9548APWR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the TCA9548APWR SCL pin?
The SCL pin has a pull-up to 3.3V on 41 of 58 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 61 open source designs using the TCA9548APWR.
What pull-up resistor is used on the TCA9548APWR SDA pin?
The SDA pin has a pull-up to 3.3V on 41 of 58 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 61 open source designs using the TCA9548APWR.
How is the TCA9548APWR A1 pin connected?
The A1 pin is tied to GND on 42 of 61 designs (a signal on 17). Counted from the KiCad layouts of 61 open source designs using the TCA9548APWR.
What parts are used alongside the TCA9548APWR?
The AMS1117-3.3, ESP32-S3-WROOM-1, USBLC6-2SC6, AP2112K-3.3 and DRV2605LDGS appear in the most repositories here.
Which microcontrollers do boards using the TCA9548APWR use?
Most are built on ESP32 (29), STM32 (8), AVR/Arduino (7) and NXP (5).
How big is a typical board using the TCA9548APWR?
The median is 94.7 × 76.2 mm, and 67% are two-layer designs.
What is the most popular open source board using the TCA9548APWR?
By GitHub stars, Zero Palm V1 by molanocortes, with 78 stars.
Can I simulate one of these boards using the TCA9548APWR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.