SoilSensor spi
angelnu·esphome·devices/pcb-pot-watering/sensor/KiCad/SoilSensor_spi.kicad_pcb
About the SoilSensor spi PCB
SoilSensor spi is an open source STM32 PCB design by angelnu, published on GitHub under the Apache-2.0 license. It is a 2-layer board measuring 29 × 110.6 mm, with 21 components from 14 distinct parts.
Its main chip is the STM32L041K6Tx, from the STM32 family. Other key parts include the SoilSonde. By type, the board carries 8 capacitors, 4 resistors, 2 ICs, 2 connectors, 1 crystal and 1 diode.
It belongs with the iot & wireless and sensors designs in this gallery.
From the project
Settings for esphome
- Aisler PCB project - KiCad schematics - - KiCad PCB - - - Parts: - 1x ESP32-WROOM-32 - 2x pression sensors LPS33HWTR - 1x accelerometer LIS3DH - 1x IC power switch MCZ33996EK - 6 or 10 RJ-45 Modular Jack - 98435-111LF - 6 or 10 connectors - PINs: - Serial programmer: 1. VCC 2. RX 3. TX 4. GND - Power - 6 or 10 pumpe power ports - 6 or 10 ethernet ports - Firmwares: - esphome - You need to modify/create your own esphome definition and include the yaml in this folder matching your PCB - Example for v1.1 - platformio For testing without esphome you can use platformio to build and standalone…

Main components on the SoilSensor spi
SoilSensor spi bill of materials (BOM)
21 components, 14 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32L041K6Tx | LQFP-32_7x7mm_P0.8mm | U1 |
| 1 | SoilSonde | soilSonde | U3 |
| 1 | 32KHz | Crystal_SMD_3215-2Pin_3.2x1.5mm | Y1 |
| 1 | Conn_01x06_Male | PinSocket_1x06_P2.54mm_Vertical | J1 |
| 1 | RJ45 | RJ45_kycon_GMX-SMT2-S-88-TR_Horizontal | J2 |
| 1 | BOOT | SW_SPST_TL3342 | BOOT1 |
| 1 | RESET | SW_SPST_TL3342 | RESET1 |
| 1 | LED | D_0805_2012Metric | D1 |
| 1 | Ferrite_Bead_Small | R_0805_2012Metric | FB1 |
| 2 | 10 pF | C_0805_2012Metric | C1, C2 |
| 4 | 100 nF | C_0805_2012Metric | C4, C5, C6, C7 |
| 2 | 1 uF | C_0805_2012Metric | C8, C10 |
| 3 | 12K | R_0805_2012Metric | R1, R3, R7 |
| 1 | 2M2 | R_0805_2012Metric | R2 |
SoilSensor spi design files
The KiCad project lives in the angelnu/esphome repository on GitHub; these links point at the commit this page was built from.
SoilSensor spi: common questions
What microcontroller does the SoilSensor spi use?
The SoilSensor spi is built around the STM32L041K6Tx, from the STM32 family.
How big is the SoilSensor spi PCB?
The SoilSensor spi measures 29 × 110.6 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the SoilSensor spi?
21 components, from 14 distinct parts. The full bill of materials is listed on this page.
Where can I download the SoilSensor spi design files?
From the angelnu/esphome repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the SoilSensor spi design in my own project?
Yes, under the terms of its Apache-2.0 license, which angelnu chose for the repository.
Can I test firmware for the SoilSensor spi without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in esphome
ESP32
Pcb power usb
angelnu
95.8 × 30.5 mm52 parts2LApache-2.024ESP32
Pot watering controller v1
angelnu
64.6 × 87.1 mm38 parts2LApache-2.024ESP32
Siedle bus
angelnu
43.5 × 37 mm34 parts2LApache-2.024ESP32
Esp32-temp
angelnu
57.1 × 56.3 mm24 parts2LApache-2.024ESP32
Pcb led lights
angelnu
61 × 28 mm24 parts2LApache-2.024
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k