Timer-Dongle
Annicat3·Timer-Dongle·PCB/Timer.Dongle.kicad_pcb
About the Timer-Dongle PCB
Timer-Dongle is an open source WCH CH32/CH55x PCB design by Annicat3, published on GitHub under the MIT license. It is a 2-layer board measuring 40.7 × 66.4 mm, with 21 components from 9 distinct parts.
Its main chip is the CH552G, from the WCH CH32/CH55x family. By type, the board carries 6 diodes, 6 resistors, 2 capacitors, 1 IC, 1 connector and 1 buzzer.
From the project
A small USB timer Dongle with 6 LEDs, a buzzer and a cute cat-shaped PCB.
Main components on the Timer-Dongle
Timer-Dongle bill of materials (BOM)
21 components, 9 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | CH552G | JEITA_SOIC-16_3.9x9.9mm_P1.27mm | U1 |
| 1 | USB_A | USB-A | J1 |
| 1 | Buzzer | Buzzer_Murata_PKMCS0909E | BZ1 |
| 1 | 10k | R_0603_1608Metric | R_SW1 |
| 1 | SW_Push | SW_SPST_TS-1088-xR020 | SW1 |
| 2 | SW_Push | SW_SPST_TS-1088-xR020 | SW_start1, SW_time1 |
| 6 | LED | LED_0805_2012Metric | D1, D2, D3, D4, D5, D6 |
| 2 | 100nF | C_0603_1608Metric | C1, C2 |
| 6 | 470 | R_0603_1608Metric | R2, R3, R4, R5, R6, R7 |
Timer-Dongle design files
The KiCad project lives in the Annicat3/Timer-Dongle repository on GitHub; these links point at the commit this page was built from.
- LayoutPCB/Timer.Dongle.kicad_pcb
- SchematicPCB/Timer.Dongle.kicad_sch
Timer-Dongle: common questions
What microcontroller does the Timer-Dongle use?
The Timer-Dongle is built around the CH552G, from the WCH CH32/CH55x family.
How big is the Timer-Dongle PCB?
The Timer-Dongle measures 40.7 × 66.4 mm, has 2 copper layers and is 1 mm thick.
How many components are on the Timer-Dongle?
21 components, from 9 distinct parts. The full bill of materials is listed on this page.
Where can I download the Timer-Dongle design files?
From the Annicat3/Timer-Dongle repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Timer-Dongle design in my own project?
Yes, under the terms of its MIT license, which Annicat3 chose for the repository.
Can I test firmware for the Timer-Dongle without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug WCH CH32/CH55x firmware against it before you order a PCB.
Similar boards
WCH CH32/CH55x
Ps2usb
rasteri
40 × 55 mm25 parts2LNo license428WCH CH32/CH55x
CH32X-48
rgoulter
224.6 × 74.2 mm112 parts2LNo license230WCH CH32/CH55x
CH32X-60-ANSI-Improved
rgoulter
285 × 94.2 mm149 parts2LNo license230WCH CH32/CH55x
CH32X-75
rgoulter
285 × 94.2 mm318 parts2LNo license230WCH CH32/CH55x
CH552-48
rgoulter
224.6 × 74.2 mm107 parts2LNo license230WCH CH32/CH55x
Webusb programmer rev6
laneboysrc
38 × 20 mm18 parts2LMIT87