23 open source boards using the CH552G

Real designs built with the CH552G, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

23 boardsClear filters|Most starred

How designs wire the CH552G

Read from the KiCad layouts of 19 open source designs, one per repository: what each pin of the CH552G connects to, and the resistors, capacitors and other passives placed on it.

  • The VCC_15 pin has a decoupling capacitor on 17 of 19 designs, most often 100 nF (then 4.7 µF).
  • The 3V3_16 pin is tied to 3.3V on 12 of 19 designs (a signal on 7).
  • The P3.6_12 pin has a series resistor on 9 of 19 designs, most often 10 kΩ (then 22 Ω).
P1.7_5pin 5Connected to: A connector 26% · not connected 16%
  • Series resistor on 32% · 330 Ω (3), 220 Ω (1), 470 Ω (1)
P3.3_10pin 10Connected to: A connector 32% · not connected 21%
  • Series resistor on 32% · 330 Ω (4), 470 Ω (1), 1 kΩ (1)
P3.4_11pin 11Connected to: A connector 32% · not connected 26%
  • Series resistor on 32% · 330 Ω (4), 220 Ω (1), 470 Ω (1)
P3.6_12pin 12Connected to: A connector 79%
  • Series resistor on 47% · 10 kΩ (6), 22 Ω (2), 5.1 kΩ (1)
GND_14pin 14Connected to: GND 100%
VCC_15pin 15Connected to: VBUS 89%
  • Decoupling capacitor on 89% · 100 nF (19), 4.7 µF (1), 10 µF (1)
3V3_16pin 16Connected to: 3.3V 63% · a signal 37%

9 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include CH552 by nicola-strappazzon, Ch552g dev board by blueOkiris, L.I.P.S. by milar111 and Pip by jnthas.

The CH552G in open source designs

The gallery holds 23 open source boards using the CH552G from 20 GitHub repositories; a typical one measures about 41.9 × 35 mm and carries around 21 components.

100% are two-layer designs, the rest use four layers or more, and 48% carry an open source license.

The most starred is CH552 by nicola-strappazzon.

Parts used alongside the CH552G

Microcontrollers on boards using the CH552G

CH552G: common questions

Where can I find a CH552G reference design?

Each of the 23 boards on this page is a real design using the CH552G. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the CH552G VCC_15 pin?

The VCC_15 pin has a decoupling capacitor on 17 of 19 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 19 open source designs using the CH552G.

How is the CH552G 3V3_16 pin connected?

The 3V3_16 pin is tied to 3.3V on 12 of 19 designs (a signal on 7). Counted from the KiCad layouts of 19 open source designs using the CH552G.

What resistor goes on the CH552G P3.6_12 pin?

The P3.6_12 pin has a series resistor on 9 of 19 designs, most often 10 kΩ (then 22 Ω). Counted from the KiCad layouts of 19 open source designs using the CH552G.

Which microcontrollers do boards using the CH552G use?

Most are built on WCH CH32/CH55x (23).

How big is a typical board using the CH552G?

The median is 41.9 × 35 mm, and 100% are two-layer designs.

What is the most popular open source board using the CH552G?

By GitHub stars, CH552 by nicola-strappazzon, with 35 stars.

Can I simulate one of these boards using the CH552G before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part