Variable gain amp
anthonykouttron·variable-gain-amp·kicad/analogamp.kicad_pcb
About the Variable gain amp PCB
Variable gain amp is an open source PCB design by anthonykouttron, published on GitHub. It is a 2-layer board measuring 61 × 63.5 mm, with 21 components from 14 distinct parts.
Other key parts include the OPA342. By type, the board carries 10 capacitors, 4 resistors, 3 connectors, 1 IC, 1 switch and 1 diode.
It belongs with the audio designs in this gallery.
From the project
Custom Analog Amplifier KiCad Design Challenge
I designed a variable analog amplifier circuit with adjustable gain in KiCad 4.0.6 An adjustable gain was implemented using a potentiometer and a variable capacitor bank was used to allow for fine adjustment of the cut-off frequency of the low pass filter. I used a traditional barrel jack for 5v imput power and two simple terminal blocks for input and output waveforms.

Main components on the Variable gain amp
Variable gain amp bill of materials (BOM)
21 components, 14 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | OPA342 | TSOT-23-5_HandSoldering | U1 |
| 1 | 1985865 0-2V INPUT SIGNAL | TerminalBlock_Pheonix_MKDS1.5-2pol | J1 |
| 1 | 1985865 0-5V OUTPUT SIGNAL | TerminalBlock_Pheonix_MKDS1.5-2pol | J2 |
| 1 | PJ-037B 5V DC INPUT | JACK_ALIM | J3 |
| 1 | 10K | Potentiometer_Trimmer_ACP_CA6v_Horizontal | RV1 |
| 1 | CHS-08TB 8PIN DIP SW | SW_DIP_x8_W7.62mm_Slide_Copal_CHS-B | SW1 |
| 1 | 20V | D_0805 | D1 |
| 1 | 100NF 100nF | C_0805_HandSoldering | C1 |
| 1 | 10UF 10uF | C_0805_HandSoldering | C2 |
| 8 | 200PF 200pf | C_0805_HandSoldering | C3, C4, C5, C6, C7, C8, C9, C10 |
| 1 | 100OHM 100 | R_0805_HandSoldering | R1 |
| 1 | 2K | R_0805_HandSoldering | R2 |
| 1 | 3K | R_0805_HandSoldering | R3 |
| 1 | 10OHM 10 | R_0805_HandSoldering | R4 |
Variable gain amp design files
The KiCad project lives in the anthonykouttron/variable-gain-amp repository on GitHub; these links point at the commit this page was built from.
Variable gain amp: common questions
How big is the Variable gain amp PCB?
The Variable gain amp measures 61 × 63.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Variable gain amp?
21 components, from 14 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Variable gain amp design files?
From the anthonykouttron/variable-gain-amp repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Variable gain amp design in my own project?
The repository has no license, so all rights stay with anthonykouttron. Use it as a reference, and ask the author before reusing the design.
Similar boards
KLOR
GEIGEIGEIST
160.2 × 118.3 mm79 parts2LGPL-3.01.2kButtonsLEDs
shanteacontrols
390 × 37 mm82 parts2LApache-2.0956USB
shanteacontrols
52 × 12.6 mm6 parts2LApache-2.0956Pots
shanteacontrols
390 × 93 mm75 parts2LApache-2.0956PicoGUS Hand386
polpo
29.2 × 75.2 mm43 parts4LGPL-2.0800Snark barker
schlae
231.1 × 106.7 mm193 parts2LNo license687